Cargador Gnb Flx 200

1.

FLX200 SERIES INDUSTRIAL BATTERY CHARGERS INSTALLATION & OPERATING INSTRUCTIONS

TABLE OF CONTENTS TITLE 1. Important Operating Instructions 2. Introduction 3. Receiving Instructions 4. Location and Installation of Charger 5. Stacking 6. AC Electrical Supply 6.1 Branch Circuit Protection 6.2 AC Voltage Connections 6.3 Ground Connection 7. DC Output 8. Fault and Display Codes 9. Options9.1 JIC Switch 9.2 Momentary Remote and Stop Operation 10. FLX200 Standard Charger Operation 11. Charger Functional Description 11.1 LED Descriptions 11.2 Display 11.3 Pause Push Button 11.4 Smart Start Stage 11.5 Auto Balance 11.6 Equalize Stage 11.7 Equalize Pushbutton 11.8 Low Battery Override/Recovery 11.9 Delayed Start of Charge 11.10 Battery Cooldown Operation Stage 11.11 Refresh Charge 11.12Charge Time 11.13 Incorrect Battery Limits 11.14 Charge Cycle Reset 11.15 AC Power Failure 12. Maintenance Appendix A Fault Codes Appendix B FLX200 Troubleshooting Appendix C Single Phase Technical Data Appendix D Three Phase Technical Data Appendix E Circuit Diagrams Appendix F Cabinet Dimensions Page 2 3 3 3 3-4 5-9 5 9 9 10 10 10 10 10 11 12 12 12 12 12 13 13 13 13 14 14 14 15 15 15 15 15 1617 18-19 20-21 22-27 28
1

Sales • Service • Recycling 1-888-563-6300

FLX200 SERIES INDUSTRIAL BATTERY CHARGERS
1. IMPORTANT OPERATING AND SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS a) Before using the battery charger, read all the instructions in addition to the CAUTION, WARNING, and DANGER markings on the charger, battery, and all the associated equipment. b) Do not touch un-insulatedparts of the DC output connector or the battery terminals, as there is a possibility of electric shock. c) Connect or disconnect the battery plug only when the charger output is off. ALWAYS press the PAUSE pushbutton before unplugging the battery to prevent arcing or burning. d) If the battery is unplugged during charging, the charger will indicate “F18”. To restart the charger, plug in the nextbattery. Do not connect the next battery before you see indication “- - - -” or “F18”. e) Only qualified personnel should operate or service this equipment. f) De-energize all AC and DC power connections before servicing this unit. If injury does occur, apply the prescribed treatment for electrical shock and obtain medical attention immediately.

g) The charger is NOT for outdoor use. Do notexpose the charger to rain or snow. h) This charger is factory set to charge lead-acid batteries only. The operating environment should not contain any materials that may cause corrosion or contamination that would degrade the performance of a charger. i) Do not operate this unit if it has received a sharp blow, been dropped or otherwise damaged. Take it to a qualified Exide Technologies Motive Powerservice center. Do not disassemble the charger. Have the charger examined by an Exide Technologies Motive Power service representative or local qualified service facility. Incorrect re-assembly of the charger may result in an explosion, electric shock or fire.

j)

k) The charger profile is set at the factory for a charger DC cable length of 9 ft and a battery DC cable length of 25 in. If DCcable lengths are adjusted, please contact your local Exide Technologies Motive Power service representative.

Sales • Service • Recycling 1-888-563-6300

2

2. INTRODUCTION The GNB® FLX200 battery chargers are fan cooled, solid state, microprocessor controlled, SCR regulated chargers designed to make battery charging simple. They are factory set to charge flooded lead-acid batteries, but anupgrade can be purchased from an Exide Technologies Motive Power service representative to enable the charger to service CHAMPION® sealed lead-acid batteries. The charger has a comprehensive self-checking diagnostic program to control all charger functions, monitor the quality of charge and check its own safety conditions. Large easy to read LEDs, two button keypad and LED display report on the...