Codigo De Route

Universidad Autonoma de Nuevo Leon
Facultad Ingeneria Mecanica y Electrica

Juan Roberto Escamilla Lopez
1879534

CISCO 2 V6
Proyecto

Router 0
Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#interface FastEthernet0/0
Router(config-if)#
Router(config-if)#exit
Router(config)#interface FastEthernet0/0Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#
Router(config-if)#exit
Router(config)#interface FastEthernet0/1
Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up
Router(config-if)#
%LINEPROTO-5-UPDOWN:Line protocol on Interface FastEthernet0/1, changed state to up
Router(config-if)#exit
Router(config)#interface FastEthernet1/0
Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface FastEthernet1/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1/0, changed state to up
Router(config-if)#
Router(config-if)#exit
Router(config)#interface FastEthernet1/1Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface FastEthernet1/1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1/1, changed state to up
Router(config-if)#
Router(config-if)#exit
Router(config)#interface Serial0/2/0
Router(config-if)#
%LINK-5-CHANGED: Interface Serial0/2/0, changed state to up
no shutdown
Router(config-if)#

Router 1Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#interface FastEthernet1/0
Router(config-if)#
Router(config-if)#exit
Router(config)#interface FastEthernet0/0
Router(config-if)#
Router(config-if)#exit
Router(config)#interface FastEthernet0/1
Router(config-if)#
Router(config-if)#exit
Router(config)#interface FastEthernet1/0Router(config-if)#
Router(config-if)#exit
Router(config)#interface FastEthernet1/1
Router(config-if)#
Router(config-if)#exit
Router(config)#interface FastEthernet0/0
Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#
Router(config-if)#exitRouter(config)#interface FastEthernet0/1
Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up
Router(config-if)#
Router(config-if)#exit
Router(config)#interface FastEthernet0/0
Router(config-if)#
Router(config-if)#exit
Router(config)#interface FastEthernet0/1Router(config-if)#
Router(config-if)#exit
Router(config)#interface FastEthernet1/0
Router(config-if)#
Router(config-if)#exit
Router(config)#interface FastEthernet1/0
Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface FastEthernet1/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1/0, changed state to up
Router(config-if)#
%LINEPROTO-5-UPDOWN: Line protocol onInterface FastEthernet1/0, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1/0, changed state to up
Router(config-if)#exit
Router(config)#interface FastEthernet1/0
Router(config-if)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1/0, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1/0, changed state to upRouter(config-if)#switchport mode trunk
Router(config-if)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1/0, changed state to down
Router(config-if)#exit
Router(config)#interface FastEthernet1/1
Router(config-if)#speed 100
Router(config-if)#duplex half
Router(config-if)#speed auto
Router(config-if)#duplex auto
Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface...