Digital

Solo disponible en BuenasTareas
  • Páginas : 6 (1260 palabras )
  • Descarga(s) : 0
  • Publicado : 27 de enero de 2011
Leer documento completo
Vista previa del texto
SN74LS00 Quad 2-Input NAND Gate
• ESD > 3500 Volts
VCC 14 13 12 11 10 9 8

http://onsemi.com

LOW POWER SCHOTTKY
1 2 3 4 5 6 7 GND

GUARANTEED OPERATING RANGES
Symbol VCC TA IOH IOL Parameter Supply Voltage Operating Ambient Temperature Range Output Current – High Output Current – Low Min 4.75 0 Typ 5.0 25 Max 5.25 70 – 0.4 8.0 Unit V °C mA mA
14 1

PLASTIC N SUFFIX CASE 646

14 1SOIC D SUFFIX CASE 751A

ORDERING INFORMATION
Device SN74LS00N SN74LS00D Package 14 Pin DIP 14 Pin Shipping 2000 Units/Box 2500/Tape & Reel

© Semiconductor Components Industries, LLC, 1999

1

December, 1999 – Rev. 6

Publication Order Number: SN74LS00/D

SN74LS00
DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)
Limits Symbol VIH VIL VIK VOHParameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage Output HIGH Voltage 2.7 – 0.65 3.5 0.25 VOL Out ut Output LOW Voltage 0.35 IIH IIL IOS In ut Input HIGH Current 0.1 Input LOW Current Short Circuit Current (Note 1) Power Supply Current ICC Total, Output HIGH Total, Output LOW 1.6 4.4 mA VCC = MAX – 20 – 0.4 –100 0.5 20 V µA mA mA mA IOL = 8.0 mA 0.4 Min 2.0 0.8 – 1.5 Typ MaxUnit V V V V V Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN, IIN = – 18 mA VCC = MIN, IOH = MAX, VIN = VIH or VIL per Truth Table IOL = 4.0 mA VCC = VCC MIN, VIN = VIL or VIH per Truth Table

VCC = MAX, VIN = 2.7 V VCC = MAX, VIN = 7.0 V VCC = MAX, VIN = 0.4 V VCC = MAX

Note 1: Not more than one output should be shorted at atime, nor for more than 1 second.

AC CHARACTERISTICS (TA = 25°C)
Limits Symbol tPLH tPHL Parameter Turn–Off Delay, Input to Output Turn–On Delay, Input to Output Min Typ 9.0 10 Max 15 15 Unit ns ns Test Conditions VCC = 5.0 V CL = 15 pF

http://onsemi.com
2

SN74LS00
PACKAGE DIMENSIONS

N SUFFIX PLASTIC PACKAGE CASE 646–06 ISSUE M
14 8

B
1 7

NOTES: 1. DIMENSIONING ANDTOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 5. ROUNDED CORNERS OPTIONAL. INCHES MIN MAX 0.715 0.770 0.240 0.260 0.145 0.185 0.015 0.021 0.040 0.070 0.100 BSC 0.052 0.095 0.008 0.015 0.115 0.135 0.290 0.310 ––– 10_ 0.015 0.039 MILLIMETERS MIN MAX 18.16 18.80 6.10 6.60 3.69 4.69 0.380.53 1.02 1.78 2.54 BSC 1.32 2.41 0.20 0.38 2.92 3.43 7.37 7.87 ––– 10_ 0.38 1.01

A F N –T–
SEATING PLANE

L C

K H G D 14 PL 0.13 (0.005)
M

J M

DIM A B C D F G H J K L M N

D SUFFIX PLASTIC SOIC PACKAGE CASE 751A–03 ISSUE F
–A–
14 8

–B–
1 7

P 7 PL 0.25 (0.010)
M

B

M

NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER.3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION.

G C

R X 45 _

F

–T–
SEATING PLANE

D 14 PL 0.25 (0.010)

K
M

M
S

J

T B

A

S

DIM A B C D F GJ K M P R

MILLIMETERS MIN MAX 8.55 8.75 3.80 4.00 1.35 1.75 0.35 0.49 0.40 1.25 1.27 BSC 0.19 0.25 0.10 0.25 0_ 7_ 5.80 6.20 0.25 0.50

INCHES MIN MAX 0.337 0.344 0.150 0.157 0.054 0.068 0.014 0.019 0.016 0.049 0.050 BSC 0.008 0.009 0.004 0.009 0_ 7_ 0.228 0.244 0.010 0.019

http://onsemi.com
3

SN74LS00

ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC(SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without...
tracking img