Instrumentacion

Introduction
- Please be sure to read and understand Precautions and Introductions in CX-One Setup Manual, CX-Programmer
Operation Manual and CX-Integrator Operation Manual before using the product.
- This Guide describes the basic operation procedure of CX-Programmer. Refer to the Help or the Operation Manual
of the PDF file for detailed descriptions.
- Acrobat Reader 5.0 or later isrequired to read the PDF files.
- You can display the PDF files from the [Start] menu on your desktop after installing the CX-Programmer.
- The screen views used in this guide may be different from the actual view, and be subject to change without notice.
- The product names, service names, function names, and logos described in this guide are trademarks or
registered trademarks of their respectivecompanies.
- The symbols (R) and TM are not marked with trademarks and registered trademarks in this guide respectively
- The product names of the other companies may be abbreviated in this guide.

Table of Contents

Chapter 1 Overview and Installation of CX-One
1. What is CX-One?
2. Features of CX-One
3. Integrated Simulation
4. CX-One Installation Procedure

1-1
1-1
1-2
1-4Chapter 2 Example of PLC System Construction by CX-One
Workflow in This Chapter
1. Design
1-1. Starting CX-Programmer
1-2. Creating Unit Configuration
1-3. Setting CPU Bus Units and Special I/O Units
1-4. Checking I/O Assignment
1-5. Programming
1-6. Offline Debug
1-7. Saving a Project
2. Online Debug on a Machine
2-1. Reading a Project
2-2. Online Connection to PLC
2-3. Transferringto a Machine
2-4. Program Debug
3. Start-Up / Adjustment On-site
3-1. Program Modification
3-2. Unit Parameter Change

2-1
2-2
2-3
2-5
2-9
2-10
2-12
2-13
2-14
2-15
2-16
2-21
2-23
2-25

Chapter 3 Example of PLC Network System Construction by CX-One
Workflow in This Chapter
1. PLC Network Start-Up
1-1. PLC Start-Up
1-2. DeviceNet Start-Up
1-3. NT Link Start-Up
1-4.Controller Link Start-Up
1-5. CompoWay/F Start-Up
1-6. Saving System Configuration
2. Adjustment On-site
2-1. System Configuration Verification
2-2. Controller Link Diagnosis
2-3. Checking CompoNet Network
3. Servo/Inverter Settings
3-1. DeviceNet Connection
3-2. RS232C Connection

3-1
3-2
3-6
3-8
3-10
3-12
3-15
3-17
3-19
3-20
3-22
3-23

1. What is CX-One?
1. What is CX-One?CX-One is an FA Integrated Tool Package that integrates Support Software for OMRON's PLC and other
Components.
To construct an FA System based mainly on PLC, traditionally it was necessary to purchase and install
individual Support Software compatible with each Unit, start the software individually, and then connect
to PLC and individual Components.
Installation of this FA Integrated ToolPackage "CX-One" on a personal computer allows integrated
operation from setup of OMRON's CPU Bus Units and Special I/O Units (SIOU) and Components to
network start-up/monitoring and improving efficiency of PLC System start-up.

2. Features of CX-One
2. Features of CX-One
CX-One allows integrated management of Support Software for OMRON's PLC/Components.
• Installation on only one personalcomputer allows a user to handle Support Software for OMRON's
products.
• Only one licensing key is required to install all Support Software.
• It allows integrated management of one save location for files created by Support Software.
Support Software dedicated to CPU Bus Units and Special I/O Units can be started on the I/O Table.
• The appropriate dedicated Support Software can beautomatically started by specifying a
registered Unit in the I/O Table (Unit configuration table attached to a PLC). In addition, setup
information such as PLC model can be passed to the dedicated Support Software at start-up,
allowing easier switching between Support Software.
The following functions are available by the introduction of the ID information file (CPS) for OMRON
Components.
• Setup of...