Air Conditioning Air Conditioning Control Assembly
AIR CONDITIONING AIR CONDITIONING CONTROL ASSEMBLY
AIR CONDITIONING CONTROL ASSEMBLY
AC3P2-01
COMPONENTS
Center Resistor LH
Center Resistor RH
Integration Control Panel Assembly
I24826
2004 LAND CRUISER (RM1071U)
Author :
Date :
2822
AC-98
AIR CONDITIONING AIR CONDITIONING CONTROL ASSEMBLY
w/ Navigation System:
Radio Receiver Bracket LH
A/CAmplifier
EMV
Radio Receiver Bracket RH
Radio Receiver
Heater Control Housing
Integration Control Panel Board Knob
I24827
2004 LAND CRUISER (RM1071U)
Author :
Date :
2823
AC-99
AIR CONDITIONING AIR CONDITIONING CONTROL ASSEMBLY
w/o Navigation System: Radio Receiver Bracket LH
Radio Receiver Bracket RH
Radio Receiver
Heater Control Housing
Knob A/CAmplifier
Board
Knob Integration Control Panel
I25152
2004 LAND CRUISER (RM1071U)
Author :
Date :
2824
AC-102
AIR CONDITIONING AIR CONDITIONING CONTROL ASSEMBLY
AC3P0-01
DISASSEMBLY
1. w/ navigation system: REMOVE KNOB Using a screwdriver, pull out the knobs. HINT: Tape up the screwdriver tip before use.
I25192
2. (a)
w/ navigation system: REMOVE INTEGRATIONCONTROL PANEL Remove the 2 screws.
I25193
(b)
Remove the screw and the board.
I24781
3. (a) (b)
I24782
4. (a) HINT: Tape up the screwdriver tip before use. (b) Remove the nut. 5. w/o LEXUS navigation system: REMOVE KNOB Using a screwdriver, pull out the knobs. HINT: Tape up the screwdriver tip before use.
w/ navigation system: REMOVE HEATER CONTROL HOUSING Disconnect theconnector clamps. Remove the 2 screws and pull out the board from the heater control housing. REMOVE KNOB Using a screwdriver, pull out the knobs.
I25159
2004 LAND CRUISER (RM1071U)
Author :
Date :
2827
AC-103
AIR CONDITIONING AIR CONDITIONING CONTROL ASSEMBLY
6. (a)
w/o navigation system: REMOVE INTEGRATION CONTROL PANEL Remove the 6 screws and pull out the A/C amplifier.I25160
(b)
Remove the 5 screws and the board.
I25161
2004 LAND CRUISER (RM1071U)
Author :
Date :
2828
AC-104
AIR CONDITIONING AIR CONDITIONING CONTROL ASSEMBLY
AC3P1-01
INSPECTION
1. w/o Navigation system: INSPECT ILLUMINATION OPERATION (a) Connect the positive (+) lead from the battery to terminal C10 and negative (-) lead to terminal C19, then check that theindicators illuminate. If operation is not as specified, check the faulty bulb. (b) Remove the bulb.
: Bulb
C10
C19
I25173
(c)
Using the tester as shown in the illustration, test the continuity. If continuity exists, replace the heater control. If no continuity exists, replace the bulb.
I07872
2.
w/o Navigation system: INSPECT INDICATORS OPERATION (a) Connect the positive (+)lead from the battery to terminal C22 and negative (-) lead to terminal C12. (b) Check that the indicators come on while operate the switches. If operation is not as specified, replace the heater control. 3. INSPECT A/C CONTROL ASSEMBLY CIRCUIT (See page DI-1309 )
C22
C12
I25174
2004 LAND CRUISER (RM1071U)
Author :
Date :
2829
AC-105
AIR CONDITIONING AIR CONDITIONINGCONTROL ASSEMBLY
4.
w/ Navigation system: INSPECT ILLUMINATION OPERATION (a) Connect the positive (+) lead from the battery to terminal A8 and negative (-) lead to terminal A16. (b) Check that the indicators come on while operating the switches. If operation is not as specified, replace the heater control. 5. INSPECT A/C CONTROL ASSEMBLY CIRCUIT (See page DI-1309 )
A8
A16
I25175
2004LAND CRUISER (RM1071U)
Author :
Date :
2830
AC-107
AIR CONDITIONING AIR CONDITIONING CONTROL ASSEMBLY
AC1JL-02
INSTALLATION
Installation is in the reverse of removal (See page AC-100 ). HINT: w/ Navigation System: When removing/installing or replacing EMV, or when disconnecting/connecting the battery terminal, turn the IG ON and OFF twice for initial display setting.
2004...
Regístrate para leer el documento completo.