Athena-Xt16

16 Temperature/Process

SERIES SERIES 16
TEMPERATURE/PROCESS ControllerCONTROLLER

Instruction Manual Operating Instructions

Introduction
Congratulations on your purchase of an Athena® Series 16 Single-Loop Controller. It is designed for ease of use and reliability wherever accurate closed-loop control is required. Your Series 16 has been configured according to your orderingspecifications as either a universal process controller or a dedicated temperature controller. In addition, special functions such as a heater break alarm, digital communications, etc., do not require you to make any internal jumper or DIP switch settings. After following the instructions for installation, simply step through and set your desired parameters using the Series 16’s easy menu system. Theinstrument may then be automatically or manually tuned to your process for optimum setpoint control. A Quick-Start Reference Card is attached to the back of the instruction manual for experienced users of PID controllers. If you still have questions or require any assistance in setting up or operating your controller, please contact your Athena representative or call 1-800-782-6776.

Safety WarningIn addition to presenting a potential fire hazard, high voltage and high temperature can damage equipment and cause severe injury or death. When installing or using this instrument, follow all instructions carefully and use approved safety controls. Electrical connections and wiring should be performed only by suitably trained personnel. Do not locate this instrument where it is subject toexcessive shock, vibration, dirt, moisture, oil or other liquids. Safe ambient operating temperature range is 32° to 131° F (0° to 55° C).

Precautions
After unpacking, inspect the instrument for any physical damage that may have occurred in shipping. Save all packing materials and report any damage to the carrier immediately.

NOTES ON CE EMC COMPLIANCE This unit is compliant with the followingstandards when properly installed in a grounded metal panel: EN55011 (CISPR 11), Class B ENS0082-1

©Copyright 1998, Athena Controls, Inc.
2 3

Table of Contents
Installation
Mounting Wiring

Table of Contents
8 8 12 15 20 28 34 34 36 37 39 Limit Controller Option Digital Communications Recalibration Procedure Error Codes Warranty/Repair Information Technical Specifications Ordering Codes41 47 55 56 57 59 62

Operation
Notes on Outputs Parameter Menu Organization Notes on Alarms Tuning

Special Functions
Auto/Manual Remote Setpoint Select Process Variable Retransmission Heater Break Alarm Transducer Excitation

4

5

Installation
Measurements between centerlines of panel cutouts are minimum recommended.

Figure 1. Recommended Panel Layout for Multiple ControllersInstallation
Figure 2. Case Dimensions
2.100" (53.3mm) 0.717" (8.21 mm)
PV

C L

2.850" (72.4 mm)

C L C L
2.150" (54.6 mm)

4.654" (118.21mm) 3.937" (100 mm)

2.100" A2 (53.3mm) F1
F2

O1 O2 A1

SV

1.750" (44.5 mm)

Prior to mounting the Series 16 in your panel, make sure that the cutout opening is of the right size, 1.771" x 1.771" (45 mm x 45 mm), and deburred to enablea smooth fit. A minimum of 4" (100 mm) of depth behind the panel is required.
Bezel Case Clip

C L
1.171" (45 mm)

Grips

Rubber Gasket

Customer Panel

Figure 3. Series 16 Mechanical Components
6 7

Mounting
Slide the mounting collar off and remove any wrapping material from the instrument. (To ease removal of the collar, gently pry up all three tabs on each side with athin-blade screwdriver.) Insert the Series 16 through the front panel cutout and slide the mounting collar back onto the unit from behind the panel. Press the tabs of the mounting collar into the ridges of the case housing. The case should now be secure in the cutout. If it can still be moved, reposition the mounting collar until the unit is completely immobile within the panel. If it is necessary to...