Ver 1.0 2002.03
HCD-RG88 is the amplifier, CD player, tape deck and tuner section in MHCRG88.
Model Name Using Similar Mechanism CD Section CD Mechanism Type Base Unit Name Optical Pick-up Name TAPE Section Model Name Using Similar Mechanism Tape Transport Mechanism Type
HCD-RG77 CDM58E-30BD60C BU-30BD60C A-MAX.3 HCD-RG77 TCM-230AWR41CSSPECIFICATIONS
The following are measured at AC 120, 220, 240V 50/60 Hz DIN power output (rated) 160 + 160 watts (6 ohms at 1 kHz, DIN) Continuous RMS power output (reference) 210 + 210 watts (6 ohms at 1 kHz, 10% THD) Inputs GAME (VIDEO): 1 Vp-p, 75 ohms (phono jack) GAME (AUDIO): Voltage 250 mV, (phono jacks) impedance 47 kilohms MD/VIDEO (AUDIO) IN: voltage 450 mV/250 mV, (phono jacks)impedance 47 kilohms MIC: sensitivity 1 mV, (phone jack) impedance 10 kilohms
CD player section
System Compact disc and digital audio system Laser Semiconductor laser (λ=795nm) Laser Output Max. 44.6 µW* *This output is the value measured at a distance of 200 mm from the objective lens surface on the Optical Pick-up Block with 7 mm aperture. Frequency response 2 Hz – 20 kHz (±0.5 dB) Wavelength 795 nm CD OPTICAL DIGITAL OUT (Square optical connector jack, rear panel) Wave length 660 nm Output Level –18 dBm
Outputs VIDEO OUT: (phono jacks)
Tape player section
Recording system Frequency response 4-track 2-channel stereo 50 – 13,000 Hz (±3 dB), using Sony TYPE I cassette
max. output level 1 Vp-p, unbalanced, Sync. negative load impedance 75 ohms accepts headphones of PHONES:(stereo mini jack) 8 ohms or more FRONT SPEAKER: accepts impedance of 6 to 16 ohms SURROUND SPEAKER: accepts impedance of 24 ohms or more SUBWOOFER accept impedance of 8 ohms or more
– Continued on next page –
COMPACT DISC DECK RECEIVER
2002C0500-1 C 2002.03
Home Audio Company Published by Sony Engineering Corporation
FMstereo, FM/AM superheterodyne tuner
FM tuner section
Notes on chip component replacement • Never reuse a disconnected chip component. • Notice that the minus side of a tantalum capacitor may be damaged by heat. Flexible Circuit Board Repairing • Keep the temperature of the soldering iron around 270 ˚C during repairing. • Do not touch the soldering iron on the same conductor of the circuit board(within 3 times). • Be careful not to apply force on the conductor when soldering or unsoldering. CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
Tuning range Antenna Antenna terminals Intermediate frequency
AM tuner section
87.5 – 108.0 MHz FM lead antenna 75 ohm unbalanced 10.7 MHz
Tuningrange Latin American models:
Middle Eastern models: Other models:
Antenna Antenna terminals Intermediate frequency
530 – 1,710 kHz (with the interval set at 10 kHz) 531 – 1,710 kHz (with the interval set at 9 kHz) 531 – 1,602 kHz (with the interval set at 9 kHz) 531 – 1,602 kHz (with the interval set at 9 kHz) 530 – 1,710 kHz (with the interval set at 10 kHz) AM loop antenna Externalantenna terminal 450 kHz
This appliance is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT MARKING is located on the rear exterior.
Power requirements Mexican models: Argentina models: Other models: 120 V AC, 60 Hz 220 V AC, 50/60 Hz 120 V, 220 V or 230 - 240 V AC, 50/60 Hz Adjustable with voltage selector 300 watts Approx. 280 x 360 x 445 mm Approx. 13.1 kg
Thefollowing caution label is located inside the unit.
Power consumption Dimensions (w/h/d) Mass :
Design and specifications are subject to change without notice.
SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS...
Leer documento completo
Regístrate para leer el documento completo.