Cisco

CCNA 2 Final Exam V4.0 Answers
1 . 

Refer to the exhibit. Given the topology shown in the exhibit, what three commands are needed to configure EIGRP on the Paris router ? (Choose three.) 
Paris(config)# router eigrp 100 
Paris(config)# router eigrp 
Paris(config-router)# network 192.168.6.0 
Paris(config-router)# network 192.168.7.0 
Paris(config-router)# network 192.168.8.0 Paris(config-router)# network 192.168.9.0 
  
2 . In a lab test environment, a router has learned about network 172.16.1.0 through four different dynamic routing processes. Which route will be used to reach this network? 
D 172.16.1.0/24 [90/2195456] via 192.168.200.1, 00:00:09, Serial0/0/0 
O 172.16.1.0/24 [110/1012] via 192.168.200.1, 00:00:22, Serial0/0/0 

R 172.16.1.0/24 [120/1] via192.168.200.1, 00:00:17, Serial0/0/0 
I 172.16.1.0/24 [100/1192] via 192.168.200.1, 00:00:09, Serial0/0/0 

  
3 . Which routing protocol maintains a topology table separate from the routing table?
IGRP 
RIPv1 
RIPv2 
EIGRP 
  

4 . Refer to the exhibit. R1 and R2 are unable to establish an adjacency. What two configuration changes will correct the problem? (Choose two.) 
Set a lower priority onR2. 
Configure the routers in the same area. 
Set a lower cost on R2 compared to R1. 
Add a backup designated router to the network. 
Match the hello and dead timers on both routers. 
  
5 . Which statement is true about the metrics used by routing protocols? 
A metric is a value used by a particular routing protocol to compare paths to remote networks. 
A common metric is used by allrouting protocols. 
The metric with the highest value is installed in the routing table. 
The router may use only one parameter at a time to calculate the metric. 
  
6 . Refer to the exhibit. Although R2 is configured correctly, host A is unable to access the Internet. Which two static routes can be configured on R1 to enable Internet connectivity for host A? (Choose two.) 
ip route 0.0.0.00.0.0.0 Fa0/0 
ip route 0.0.0.0 0.0.0.0 Fa0/1 
ip route 0.0.0.0 0.0.0.0 10.1.1.1 
ip route 0.0.0.0 0.0.0.0 10.1.1.2 
ip route 209.165.202.0 255.255.255.0 10.1.1.1 
ip route 209.165.202.0 255.255.255.0 10.1.1.2 
  
7 . Refer to the exhibit. Host A is unable to access the Internet. What is the reason for this? 
The IP address of host A is incorrect. 
The default gateway of host A is incorrect. The Fa0/1 interfaces of the two routers are configured for different subnets. 
The subnet mask for the Fa0/0 interface of R1 is incorrect. 
  
8 . 

Refer to the exhibit. Two routers are unable to establish an adjacency. What is the possible cause for this? 
The two routers are connected on a multiaccess network. 
The hello and dead intervals are different on the two routers. 
They havedifferent OSPF router IDs. 
They have different process IDs. 
  
9 . 

Refer to the exhibit. R1 knows two routes, Path A and Path B, to the Ethernet network attached to R3. R1 learned Path A to network 10.2.0.0/16 from a static route and Path B to network 10.2.0.0/16 from EIGRP. Which route will R1 install in its routing table? 
Both routes are installed and load balancing occurs across bothpaths. 
The route via Path B is installed because the EIGRP route has the best metric to network 10.2.0.0/16. 
The route via Path A is installed because the static route has the best metric to network 10.2.0.0/16. 
The route via Path B is installed because the EIGRP route has the lowest administrative distance to network 10.2.0.0/16. 
The route via Path A is installed because the static routehas the lowest administrative distance to network 10.2.0.0/16. 
  
10 . Refer to the exhibit. A ping between the serial interfaces of R1 and R2 is successful, but a ping between their FastEthernet interfaces fails. What is the reason for this problem? 
The FastEthernet interface of R1 is disabled. 
One of the default routes is configured incorrectly. 
A routing protocol is not configured on...