Darwin

ERouting OSPF PT Practice SBA
A few things to keep in mind while completing this activity:
1. Do not use the browser Back button or close or reload any Exam windows during the exam.
2. Do not close Packet Tracer when you are done. It will close automatically.
3. Click the Submit Assessment button to submit your work.

Introduction
In this practice Packet Tracer Skills Exam, you will:
yfinish the configuration of a partially configured network

y

establish connectivity to the East Region and the Internet through the use of static and
dynamic routing

Addressing Table
Device

Interface

Address

Subnet Mask

S0/0/0

172.16.100.245

255.255.255.252

S0/0/1

172.16.100.241

255.255.255.252

Fa0/0

172.16.100.1

255.255.255.128

Fa0/1172.16.100.238

255.255.255.240

S0/0/0

172.16.100.246

255.255.255.252

n/a

Lo0

10.0.0.1

255.255.255.255

n/a

Fa0/0

172.16.100.129

255.255.255.192

n/a

Fa0/1

172.16.100.225

255.255.255.240

n/a

S0/0/0

172.16.100.242

255.255.255.252

n/a

Lo0

10.0.0.2

255.255.255.255

n/a

Fa0/0

172.16.100.193

255.255.255.224

n/a

Fa0/1172.16.100.226

255.255.255.240

n/a

Lo0

10.0.0.3

255.255.255.255

n/a

W PC1

NIC

172.16.100.126

255.255.255.128

172.16.100.1

W PC2

NIC

172.16.100.190

255.255.255.192

172.16.100.129

NetAdmin

NIC

172.16.100.130

255.255.255.192

172.16.100.129

Payroll

NIC

172.16.100.194

255.255.255.224

172.16.100.193

W estHQ

Default GatewayS0/1/0
S0/1/1
Lo0

W -Branch1

W -Branch2

ServerFarm

n/a

Note: The password for user EXEC mode is cisco. The password for privileged EXEC mode
is class.

Step 1: Connect the Devices.
y

Connect W estHQ S0/0/1 to W-Branch2 S0/0/0. W estHQ is the DCE side of the link and is
setting the clock rate.

y

Connect W-Branch2 to an available interface on WSw.

Step 2: Configurethe Device Basics.
Note: Initially, you can only access router W-Branch2 through the console connection on
NetAdmin.
a. Configure the following on W-Branch2:
y

The router name is WB2.

y

The privileged EXEC mode uses the following encrypted password: class.

y

Enable Telnet and console line login using the following password: cisco.

y

Configure the banner message-of-the-dayas Authorized access only!

b. Configure and verify interface addressing on W-Branch2.
y

Using the Addressing Table, configure and activate all the necessary interfaces
on W-Branch2.

y

Verify connectivity.

c. Configure the correct IP addresses on W PC2 and W-Branch1.
y

Configure W PC2 with the last IP address in the subnet.

y

Configure the Fa0/1 interface on W-Branch1with the last IP address in the
subnet.

d. Verify connectivity.

Step 3: Discover the Network.
y

Explore the network to determine the IP addressing of the serial interfaces that W estHQ
shares with W-Branch1 and W-Branch2.

y

Remotely access W estHQ.

Step 4: Configure Static and Default Routing.
a. Configure connectivity to the East Region.
y

Using the next hop address192.0.0.2, configure one summary static route on
W estHQ for the entire East Region. The summary should include addresses
reserved for future expansion. The East Region subnets are listed in the following
table: 192.168.0.0/23

WHQ(config)#ip route 192.168.0.0 255.255.254.0 192.0.0.2

East Region Subnets
192.168.1.248/30
192.168.1.252/30
192.168.1.244/30
192.168.0.0/25
192.168.0.128/25192.168.1.0/26
192.168.1.64/26
192.168.1.128/26
192.168.1.192/27
192.168.1.224/28
192.168.1.240/30

y

Configure a default route on W estHQ to send to the Internet all other traffic for
destinations that are not found in the W estHQ routing table. Use the outbound
interface argument. WHQ(config)#ip route 0.0.0.0 0.0.0.0 s0/1/0

b. Verify static and default routing.

Step 5: Configure...