Engineering manual
10 January 2003
Errata Sheet No. 1 Engineering and Design Liquid Process Piping EM 1110-1-4008 5 May 1999 Reference to MSS SP -119 on page A-6, paragraph A-1 is in error. The title of the document is incorrect. Page A-6, paragraph A-1: The title for MSS SP -119 should be as follows: Belled End Socket Welding Fittings, Stainless Steel and Copper -Nickel.
CEMP-RA Engineer Manual1110-1-4008
Department of the Army
EM 1110-1-4008 5 May 1999
U.S. Army Corps of Engineers
Washington, DC 20314-1000
Engineer and Design LIQUID PROCESS PIPING
Distribution Restriction Statement
Approved for public release; distribution is unlimited.
EM 1110-1-4008 5 May 1999 US Army Corps of Engineers
ENGINEERING AND DESIGN
Liquid Process Piping
ENGINEER MANUALAVAILABILITY Electronic copies of this and other U.S. Army Corp of Engineers publications are available on the Internet at http://www.usace.army.mil/inet/usace-docs/. This site is the only repository for all official USACE engineer regulations, circulars, manuals, and other documents originating from HQUSACE. Publications are provided in portable document format (PDF).
CEMP-RA
DEPARTMENT OFTHE ARMY U.S. Army Corps of Engineers Washington, DC 20314-1000
EM 1110-l-4008
Manual No. 1110-l-4008 Engineering and Design LIQUID PROCESS PIPING
5 May 1999
1. The purpose of this manual is to provide information for the design of liquid process piping. 2. Applicability. This manual applies to all HQUSACE elements and all USACE Commands having responsibility for the design of unitprocesses for treatment of liquids. 3. Distribution Restriction. Approved for public release; distribution is unlimited. 4. References. References are provided in Appendix A. 5. Scope. This manual is to be used in the selection of piping systems and materials for chemical and physical unit processes. Process piping systems include pipe and appurtenances used to transport fluids. Separate guidance hasbeen provided for plumbing, potable water, sewage, storm drainage, fuel and lubricant systems. 6. Discussion. This manual includes criteria for the design of component parts and assemblies of liquid process piping systems. Compliance with these criteria requires that fundamental design principles are followed. Modification or additions to existing systems solely for the purpose of meeting criteriain this manual are not authorized. FOR THE COMMANDER:
4 Appendices (See Table of Contents)
Major General, U. S. Army Chief of Staff
CEMP-RA Manual No. 1110-1-4008
DEPARTMENT OF THE ARMY U.S. Army Corps of Engineers Washington, DC 20314-1000
EM 1110-1-4008
5 May 1999
Engineering and Design LIQUID PROCESS PIPING TABLE OF CONTENTS
SUBJECT PARAGRAPH PAGE SUBJECT PARAGRAPH PAGEChapter 1 Introduction Purpose . . . . . . . . . . . . . . . . . . . . . . . Applicability . . . . . . . . . . . . . . . . . . . References . . . . . . . . . . . . . . . . . . . . . Distribution . . . . . . . . . . . . . . . . . . . . Scope . . . . . . . . . . . . . . . . . . . . . . . . . Metrics . . . . . . . . . . . . . . . . . . . . . . . . Brand Names . . . . . . . . . . . . . . . . . . .Accompanying Guidance Specification . . . . . . . . . . . . . . . . . . Manual Organization . . . . . . . . . . . . . Chapter 2 Design Strategy Design Analyses . . . . . . . . . . . . . . . . Specifications . . . . . . . . . . . . . . . . . . . Drawings . . . . . . . . . . . . . . . . . . . . . . Bases of Design . . . . . . . . . . . . . . . . . Loading Conditions . . . . . . . . . . . . . . PipingLayout . . . . . . . . . . . . . . . . . . . Chapter 3 General Piping Design Materials of Construction . . . . . . . . . Design Pressure . . . . . . . . . . . . . . . . . Sizing . . . . . . . . . . . . . . . . . . . . . . . . . Stress Analysis . . . . . . . . . . . . . . . . . . Flange, Gaskets and Bolting Materials . . . . . . . . . . . . . . . . . . . . . Pipe Identification . . . . . . . . ....
Regístrate para leer el documento completo.