Eprom

M27C1001
1 Mbit (128Kb x8) UV EPROM and OTP EPROM
s

5V ± 10% SUPPLY VOLTAGE in READ OPERATION ACCESS TIME: 35ns LOW POWER CONSUMPTION: – Active Current 30mA at 5Mhz – Standby Current 100µA
1 1 32 32

s s

s s s

PROGRAMMING VOLTAGE: 12.75V ± 0.25V PROGRAMMING TIME: 100µs/word ELECTRONIC SIGNATURE – Manufacturer Code: 20h – Device Code: 05h

FDIP32W (F)

PDIP32 (B)

DESCRIPTIONThe M27C1001 is a 1 Mbit EPROM offered in the two ranges UV (ultra violet erase) and OTP (one time programmable). It is ideally suited for microprocessor systems requiring large programs and is organized as 131,072 words of 8 bits. The FDIP32W (window ceramic frit-seal package) and the LCCC32W (leadless chip carrier package) have a transparent lids which allow the user to expose the chip toultraviolet light to erase the bit pattern. A new pattern can then be written to the device by following the programming procedure. For applications where the content is programmed only one time and erasure is not required, the M27C1001 is offered in PDIP32, PLCC32 and TSOP32 (8 x 20 mm) packages.

LCCC32W (L)

PLCC32 (K)

TSOP32 (N) 8 x 20 mm

Figure 1. Logic Diagram

VCC

VPP

17 A0-A168 Q0-Q7

P E G

M27C1001

VSS
AI00710B

January 2000

1/17

M27C1001
Figure 2A. DIP Connections Figure 2B. LCC Connections

VPP A16 A15 A12 A7 A6 A5 A4 A3 A2 A1 A0 Q0 Q1 Q2 VSS

1 32 2 31 3 30 4 29 5 28 6 27 7 26 8 25 M27C1001 9 24 10 23 11 22 12 21 13 20 14 19 15 18 16 17
AI00711

VCC P NC A14 A13 A8 A9 A11 G A10 E Q7 Q6 Q5 Q4 Q3

A7 A6 A5 A4 A3 A2 A1 A0 Q0

A12 A15A16 VPP VCC P NC 1 32 A14 A13 A8 A9 A11 G A10 E Q7 9 M27C1001 25 17 VSS Q3 Q4 Q5 Q6
AI00712

Figure 2C. TSOP Connections

Table 1. Signal Names
A0-A16 Q0-Q7 Address Inputs Data Outputs Chip Enable Output Enable Program Program Supply Supply Voltage Ground Not Connected Internally

A11 A9 A8 A13 A14 NC P VCC VPP A16 A15 A12 A7 A6 A5 A4

1

32

8 9

M27C1001 (Normal)

25 24

1617
AI01151B

G A10 E Q7 Q6 Q5 Q4 Q3 VSS Q2 Q1 Q0 A0 A1 A2 A3

E G P VPP VCC VSS NC

2/17

Q1 Q2

M27C1001
Table 2. Absolute Maximum Ratings (1)
Symbol TA TBIAS TSTG VIO (2) VCC VA9 (2) VPP Parameter Ambient Operating Temperature (3) Temperature Under Bias Storage Temperature Input or Output Voltage (except A9) Supply Voltage A9 Voltage Program Supply Voltage Value –40 to 125 –50 to125 –65 to 150 –2 to 7 –2 to 7 –2 to 13.5 –2 to 14 Unit °C °C °C V V V V

Note: 1. Except for the rating ”Operating Temperature Range”, stresses above those listed in the Table ”Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only and operation of the device at these or any other conditions above those indicated in the Operating sections of thisspecification is not implied. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability. Refer also to the STMicroelectronics SURE Program and other relevant quality documents. 2. Minimum DC voltage on Input or Output is –0.5V with possible undershoot to –2.0V for a period less than 20ns. Maximum DC voltage on Output is VCC +0.5V with possible overshoot to VCC +2Vfor a period less than 20ns. 3. Depends on range.

Table 3. Operating Modes
Mode Read Output Disable Program Verify Program Inhibit Standby Electronic Signature
Note: X = VIH or VIL, VID = 12V ± 0.5V.

E VIL VIL VIL VIL VIH VIH VIL

G VIL V IH V IH VIL X X VIL

P X X VIL Pulse VIH X X VIH

A9 X X X X X X VID

VPP VCC or VSS VCC or VSS VPP VPP VPP VCC or VSS VCC

Q7-Q0 Data OutHi-Z Data In Data Out Hi-Z Hi-Z Codes

Table 4. Electronic Signature
Identifier Manufacturer’s Code Device Code A0 VIL VIH Q7 0 0 Q6 0 0 Q5 1 0 Q4 0 0 Q3 0 0 Q2 0 1 Q1 0 0 Q0 0 1 Hex Data 20h 05h

3/17

M27C1001
Table 5. AC Measurement Conditions
High Speed Input Rise and Fall Times Input Pulse Voltages Input and Output Timing Ref. Voltages ≤ 10ns 0 to 3V 1.5V Standard ≤ 20ns 0.4V to 2.4V...