Eswitching basic switching/wireless

ESwitching Basic Switching/Wireless PT Practice SBA A few things to keep in mind while completing this activity: Do not use the browser Back button or close or reload any Exam windows during the exam. Do not close Packet Tracer when you are done. It will close automatically. Click the Submit Assessment button to submit your work. Introduction In this practice Packet Tracer Skills Exam, you will:configure VLANs using VTP configure inter-VLAN routing modify STP configure port security add a wireless LAN Addressing Table Device Interface Address Subnet Mask Default Gateway Router1 Fa0/0.10 172.16.10.1 255.255.255.0 n/a Fa0/0.20 172.16.20.1 255.255.255.0 n/a Fa0/0.43 172.16.43.1 255.255.255.0 n/a Fa0/0.67 172.16.67.1 255.255.255.0 n/a WRS Internet 172.16.67.10 255.255.255.0 172.16.67.1Wireless 172.16.100.1 255.255.255.0

n/a SW_DS1 VLAN 43 172.16.43.11 255.255.255.0 172.16.43.1 SW_AC2 VLAN 43 172.16.43.12 255.255.255.0 172.16.43.1 SW_AC3 VLAN 43 172.16.43.13 255.255.255.0 172.16.43.1 PC1 NIC 172.16.10.10 255.255.255.0 172.16.10.1 PC2 NIC 172.16.20.10 255.255.255.0 172.16.20.1 PC3 NIC 172.16.10.11 255.255.255.0 172.16.10.1 PC4 NIC DHCP assigned 255.255.255.0 172.16.100.1 Note: Thepassword for user EXEC mode is cisco. The password for privileged EXEC mode is class. Step 1: Connect the Devices. Use the appropriate cable type to make the following connections: SW_AC2 FastEthernet 0/1 to PC1 SW_AC2 FastEthernet 0/11 to PC2 SW_AC2 FastEthernet 0/19 to SW_AC3 FastEthernet 0/19 SW_AC2 FastEthernet 0/20 to SW_AC3 FastEthernet 0/20 SW_AC3 FastEthernet 0/18 to WRS

Step 2:Configure the Device Basics. a. Configure the following on SW_AC2. · The switch name is SW_AC2. Switch>enable Switch#configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)#hostname SW_AC2 SW_AC2(config)# · The privileged EXEC mode uses the following encrypted password: class

SW_AC2#config t Enter configuration commands, one per line. End with CNTL/Z.SW_AC2(config)#enable password class SW_AC2(config)#exit SW_AC2# · Enable Telnet and console line login using the following password: cisco

SW_AC2#configure terminal Enter configuration commands, one per line. End with CNTL/Z. SW_AC2(config)#line console 0 SW_AC2(config-line)#login % Login disabled on line 0, until 'password' is set SW_AC2(config-line)#password cisco SW_AC2(config-line)#exitSW_AC2(config)#line vty 0 SW_AC2(config-line)#password cisco SW_AC2(config-line)#exit

·

Configure the banner message-of-the-day as Authorized access only!

SW_AC2(config)#banner motd # Enter TEXT message. End with the character '#'. Authorized acces only ! # SW_AC2(config)#

b. To configure the switches for remote management access, create and enable interface VLAN 43 on all three switches.SW_AC2(config)#interface vlan43 SW_AC2(config-if)#no shutdown

SW_AC2(config-if)#ip address 172.16.43.12 255.255.255.0 SW_AC2(config-if)#exit SW_AC2(config)# SW_AC2(config)#end SW_AC2#

Step 3: Configure Trunking. Note: Packet Tracer now supports the use of the range argument for the interface command. For interfaces FastEthernet 0/19 through FastEthernet 0/24 on all three switches: Configurestatic trunking. Assign VLAN 43 as the native VLAN.

SW_AC2(config)#int r f 0/19-24 SW_AC2(config-if-range)#switchport mode trunk SW_AC2(config-if-range)#switchport trunk native vlan 43 SW_AC2(config-if-range)#no shutdown SW_AC2(config-if-range)#end

Step 4: Configure VTP and VLANs. a. · · · b. · · · · Step 1: Configure SW_DS1 as VTP server and the following VTP parameters: SW_DS1 is the VTPserver. VTP domain name: CCNA VTP password: cisco Create and name the following VLANs on SW_DS1. VLAN 10: Student VLAN 20: Faculty VLAN 43: Management VLAN 67: Wireless

c.

Step 2: Configure SW_AC2 and SW_AC3 as VTP clients to participate in the CCNA VTP domain.

d.

Step3: Verify that VTP is operational.

Step 5: Configure Interfaces for VLAN Access VLAN port assignments on each...