Ficha Tecnica 580M S3

580 M
SERIES 3 LOADER/BACKHOE TIER III CERTIFIED
ENGINE
Model Type Cylinders Bore/Stroke Displacement Fuel injection Fuel Fuel filter Air intake Cooling Engine speeds* (rpm) Rated speed, full load Low idle High idle, no load Horsepower Gross Net Case Family III 445T/M3 diesel, Tier III certified 4-stroke, turbocharged 4 4.09 in x 5.19 in (104 x 132 mm) 274 in3 (4.5 L) Direct Diesel w/watertrap Cross-flow Liquid 2200 875 - 1025 2300 - 2450

POWERTRAIN
Transmission 4-speed synchromesh with hydraulically actuated clutches and electric F/R shuttle control, clutch disconnect buttons on the transmission shifter and loader control lever Gear ratios 1st 2nd 3rd 4th Torque converter Ratio Differential lock Front axle Differential ratio Planetary hub ratio Total reduction ratio Rear axleDifferential ratio Planetary hub ratio Total reduction ratio Service brakes Individually applied, power assisted, hydraulically actuated, maintenance-free, self-adjusting, outboard mounted, wet disc, 2 per side Disc area Parking brakes Spring applied hydraulic release (SAHR) 7 blade suction 19.2 in (488 mm) 1.1:1 Integral Reverse Travel speeds – mph (km/h) 1st Forward 3.8 (6.1) 4.5 (7.3) 2nd 6.1(9.8) 7.3 (11.7) 3rd 12.9 (20.8) 15.5 (24.9) 4th 24.3 (39.1) 29.1 (46.9) 384 in2 (.25 m2) 2.5 6.4 16.0 2.0 6.0 12.0 3.223 On-the-go push-button activation Forward 5.603 3.481 1.584 0.793 Reverse 4.643 2.884 1.313 0.657

HYDRAULICS
Pump Gear-type, transmission driven coupled directly to the engine Main relief pressure 3050 + 50 - 50 psi @ 28.5 gpm (210 + 3 - 3 bar @ 108 L/min) Filtration7-micron, full flow replaceable cartridge on return line, condition indicator light for filter Oil cooler Heavy-duty

Loader flow @ rated engine rpm 28.5 gpm @ 3050 psi (108L/min @ 210 bar) Loader control valve Monoblock single lever control for lift, tilt and auxiliary hydraulics, positive hold float and return-to-dig Loader auxiliary hydraulics proportional thumb switch w/detent on loader controlhandle. Loader auxiliary hydraulics with full available flow. 0 – 28.5 gpm (0 – 108 L/min) Backhoe flow @ rated engine rpm 28.5 gpm @ 3050 psi (108 L/min @ 210 bar)

84 (63 kW) @ 2200 rpm 79 (59 kW) @ 2200 rpm

Maximum torque @ 1400 rpm Gross 276 lb·ft (374 N·m) Net 271 lb·ft (367 N·m) Torque rise at rated speed
NOTE: Meets federal emission regulations.

36%

ENGINE COOLING
Radiator Coretype Core size area Rows of tubes Fan Style Diameter Ratio Water pump Style Square wave 487 in2 (.315 m2) 3

Manual Backhoe Controls Backhoe Control Valve Monoblock open-center, parallel circuits. Boom and dipper, with pilot operated checks Pilot Backhoe Controls Pressure compensated backhoe hydraulics for simultaneous multifunction operation. 6, 7 or 8 spool sectional closed center with opencenter inlet and circuits in parallel. Backhoe Control Valve Sectional closed-center with inlet compensator and circuits in parallel Backhoe auxiliary hydraulics Uni-directional flow, adjustable variable flow from 0 to 28.5 gpm (108 L/min) Control operation Manual Pilot Foot switch activated Button on left joystick

Engine oil Deep sump plate cooler Pump with pressurized under-piston nozzlesPump operating angle ratings Side-to-side Rated 35° Fore and aft Rated 35° Oil filtration Replaceable, full-flow cartridge

NOTE: Travel speeds at 2283 engine rpm with 19.5 x 24 tires. Speeds decrease with 17.5L x 24 rear tires.

ELECTRICAL
Voltage 12 volts, negative ground 90 amp 850 cold-cranking amps (2) 850 cold-cranking amps (2) 30 amps ea. Alternator Battery Optional batteries Power plugsTIRES
Front 2WD – 11L x 16.1, 10-ply rating 4WD – 12 x 16.5, 8-ply rating Rear 2/4WD – 17.5L x 24, 10-ply rating 2/4WD – 19.5L x 24, 10-ply rating

Bi-Directional flow, variable flow from 0 to 28.5 gpm (108 L/min) @ rated engine rpm Control 0peration Manual Pilot Hand lever Buttons on left joystick

Page 1 of 6

OPERATOR ENVIRONMENT
ROPS/FOPS canopy Key start Hydrostatic steering...