Graphtec Plotter Driver

Graphtec Plotter Driver OPS628 Ver. 7.52
for Microsoft Windows 95/98/Me

Thank you for choosing the Graphtec OPS628 Plotter Driver.
The file provides instructions and notes on installation and operation as well
as other information.
Be sure to read through this file carefully before attempting to install or
use this driver.

CONTENTS

1. OVERVIEW

2. INSTALLATION
2-1Checking the Program Disk
2-2 When connecting the FC5100 or CE3000, FC3600 via USB
2-3 Installing the Plotter Driver

3. CONFIGURING THE PLOTTER DRIVER
3-1 Selecting the Communications Port
3-2 Selecting the Paper Mode
3-3 Selecting the Paper Size
3-4 Selecting the Page Orientation
3-5 Specifying the Number of Copies (Penless Plotters and Inkjet Plotters)3-6 Setting the Unit
3-7 Setting the Pen Parameters
3-8 Setting the Allowable Color Value Range
3-9 Adjusting the Resolution of the Line Width
3-10 Selecting the Chart Feed Mode
3-11 Setting the Programmable Resolution
3-12 Printing a Cut Line (GX3000 Pen Plotter)
3-13 Setting the Programmable Resolution (Pen Plotters and Cutting Plotters)
3-14Setting the Resolution (Penless Plotters, Inkjet Plotters, and PT-5M)
3-15 Setting the Line Pitch
3-16 Setting the Scaling Factor
3-17 Selecting the Output Method for TrueType Fonts
3-18 Enabling the Clipping Function (Pen Plotters, Cutting Plotters, and
Penless Plotters)
3-19 Enabling Data Output in Binary Format
3-20 Rotating an Image by 90 Degrees (PenlessPlotters)
3-21 Rotating an Image by 90, 180, or 270 Degrees (Pen Plotters, Cutting
Plotters, and Inkjet Plotters)
3-22 Enabling Automatic Layout (Penless Plotters)
3-23 Performing Long-axis Printing (Pen Plotters, Penless Plotters, and
Inkjet Plotters)
3-24 Setting the Offset for the Origin Point
3-25 Selecting the Print Quality (Inkjet Plotters)3-26 Selecting the Media Type (JC9x00)
3-27 Selecting the Color or Mono Printing Mode (Inkjet Plotters)
3-28 Selecting the Cutting Method (JC9x00)
3-29 Selecting the Print Mode (JX1130/1060)
3-30 Setting the Save Media parameter (JX1130/1060)
3-31 Setting the Media Save parameter (JX2100/2150)
3-32 Setting the Feed Cutting Position (JX2100/2150)
3-33 Selecting theDrying Time (Inkjet Plotters)
3-34 Select the Cut Line (JX1130/1060, JX2100/2150)
3-35 Setting the Allowable Color Value Range for the Cut Line (JX2100/2150)
3-36 Setting the Step Pass (JX2100/2150)
3-37 Setting the Printing Cut Line (JX2100/2150)
3-38 Setting the Cutting Conditions (JX2100/2150)
3-39 Selecting the Dotted Line Setting (JX2100/2150)
3-40Selecting the Output Method (Penless Plotters and Inkjet Plotters)
3-41 Setting the Output Modes (JX2100/2150)
3-42 Selecting the Type of Data to Be Transferred (Penless Plotters)
3-43 Selecting the Dithering Mode (Penless Plotters and Inkjet Plotters)
3-44 Selecting the Driver's Application (Penless Plotters and Inkjet
Plotters)
3-45 Selecting the Size of Memory forProcessing Raster Data (Penless
Plotters and Inkjet Plotters)
3-46 Selecting Colors for Monochrome Bit-Mapping (Penless Plotters and
Inkjet Plotters)
3-47 Outputting Vector Data as Half-Tones (Penless Plotters and Inkjet
Plotters)
3-48 Emphasizing Lines of One-Dot Width (Penless Plotters and Inkjet
Plotters)
3-49 Enabling the Gradationof Line Output (JC9x00)
3-50 Printing of Registration Marks (JX2100/2150)
3-51 Aligning of Registration Marks (JX1130/1060)
3-52 Selecting the type of Ink (JX2100/2150)
3-53 Adjusting the Definition of Colors (JC9x00, JX2100/2150)
3-54 Selecting a Color Table File (JC9x00)
3-55 Selecting the Print Settings File (JX2100/2150)
3-56 Selecting the Print Quality...