Guias

TM-T88III
User’s Manual / Bedienungsanleitung
Gebruikershandleiding / Manuel d’utilisation
Manual do utilizador / Manual del usuario
Manuale dell’utente

410031701

Printer Parts
1 printer cover
4 control panel

2 cutter cover

POWER

PO
WE
ER
R
RO
R
P
OU APE
R
FE T
ED

ERROR
PAPER
OUT
FEED

3 cover open button

DIP Switch Tables
Serial

Parallel

SWFunction

ON

OFF

SW

Function

ON

OFF

1-1 Data receive error

Ignored

Prints “?”

1-1

Auto line feed

Always disabled

1-2 Receive buffer capacity

45 bytes

4K bytes

Always
enabled

1-2

Receive buffer
capacity

45 bytes

4K bytes

1-3

Select paper
sensors to output
paper-end
signals (default
value of ESC c 3)

Disabled

Paper roll endsensor enabled,
Paper roll nearend sensor
enabled

1-3 Handshaking

XON/XOFF

DTR/DSR

1-4 Data word length

7 bits

8 bits

1-5 Parity check

Enabled

Disabled

1-6 Parity selection

Even

Odd

1-7 Transmission speed (See table below.)
1-8

1-4~ Undefined
1-8

Transmission speed (bps)-bits per second

1-7

1-8

38400

ON

ON

SW

Function

ON

OFF4800

OFF ON

2-1

9600

ON

Handshaking
(BUSY condition)

Receive
buffer full

Offline or
Receive
buffer full

19200

OFF OFF

2-2

Do not change

OFF

2-3
2-4

Print density/Low
power

See Table A

Offline or
Receive
buffer full

2-5

Release
condition of
receive buffer
BUSY (If receive
buffer capacity
set to 4 KB.)

Releases BUSY
whenremaining receive
buffer capacity reaches
138 bytes.

SW

Function

2-1

Handshaking
Receive
(BUSY condition) buffer full

ON

2-2

Do not change

2-3
2-4

Print density/
Low power

See Table A

2-5

Release
condition of
receive buffer
BUSY (If receive
buffer capacity
set to 4 KB.)

Releases BUSY
when remaining receive
buffer capacity reaches
138 bytes.

OFFReleases BUSY
when remaining receive
buffer capacity reaches
256 bytes.

2-6

Do not change

2-7

I/F pin 6 reset

Enabled

Disabled

2-8

I/F pin 25 reset

Enabled

Disabled

Releases BUSY
when remaining receive
buffer capacity reaches
256 bytes.

2-6~ Do not change
2-7
2-8

I/F pin 31 reset (Do not change)

Table A
Print density/low power

SW 2-3

SW 2-4– Low power consumption mode

ON

ON

1 (Normal)

OFF

OFF

2 (Medium)

ON

OFF

3 (Dark)

OFF

ON

English
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any
form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written
permission of Seiko EpsonCorporation. No patent liability is assumed with respect to the use of the information
contained herein. While every precaution has been taken in the preparation of this book, Seiko Epson Corporation
assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use
of the information contained herein.
Neither Seiko Epson Corporation nor itsaffiliates shall be liable to the purchaser of this product or third parties for
damages, losses, costs, or expenses incurred by purchaser or third parties as a result of: accident, misuse, or abuse of
this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.) failure to
strictly comply with Seiko Epson Corporation’s operating and maintenanceinstructions.
Seiko Epson Corporation shall not be liable against any damages or problems arising from the use of any options or
any consumable products other than those designated as Original Epson Products or Epson Approved Products by
Seiko Epson Corporation.
EPSON and ESC/POS are registered trademarks of Seiko Epson Corporation in the U.S. and other countries.
NOTICE: The contents of this...