Hcd-w300

HCD-DR4/DR5/DR6/DR440/ W300/W5000/XB500

SERVICE MANUAL

US Model
HCD-W300/W5000

Canadian Model
HCD-W300

AEP Model UK Model
HCD-XB500

E Model
HCD-DR4/DR5/DR6/DR440
HCD-DR4/DR5/DR6/DR440/W300/W5000/ XB500 is the tuner, deck, CD and amplifier section in LBT-DR4/DR5/DR6/DR440/W300/ W5000/XB500.

Australian Model
HCD-DR4
Photo: HCD-DR6

Model Name Using Similar Mechanism CDSECTION CD Mechanism Type Base Unit Type Optical Pick-up Type TAPE DECK SECTION Model Name Using Similar Mechanism Tape Transport Mechanism Type

HCD-D290/G3300/XB3 CDM37M-5BD32L BU-5BD32L KSS-213D/Q-N NEW TCM-230AWR2/230PWR2

SPECIFICATIONS

— Continued on next page —

COMPACT DISC DECK RECEIVER
MICROFILM

–1–

–2–

CAUTION

SAFETY CHECK-OUT After correcting the original serviceproblem, perform the following safety checks before releasing the set to the customer: Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below. LEAKAGE The AC leakage from any exposed metal part to earth Ground and from all exposed metal parts to any exposed metal part having a return to chassis, mustnot exceed 0.5 mA (500 microampers). Leakage current can be measured by any one of three methods. 1. A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers’ instructions to use these instruments. 2. A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job. 3. Measuring the voltage drop across a resistor by means ofa VOM or battery-operated AC voltmeter. The “limit” indication is 0.75 V, so analog meters must have an accurate low-voltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2V AC range are suitable. (See Fig. A)

Use of controls or adjustments or performance of procedures other than thosespecified herein may result in hazardous radiation exposure. Notes on chip component replacement • Never reuse a disconnected chip component. • Notice that the minus side of a tantalum capacitor may be damaged by heat. Flexible Circuit Board Repairing • Keep the temperature of soldering iron around 270˚C during repairing. • Do not touch the soldering iron on the same conductor of the circuit board(within 3 times). • Be careful not to apply force on the conductor when soldering or unsoldering. Laser component in this product is capable of emitting radiation exceeding the limit for Class 1. This appliance is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT MARKING is located on the rear exterior. This caution label is located inside the unit.

To Exposed Metal Parts on Set0.15µF

1.5kΩ

AC voltmeter (0.75V)

Earth Ground

Fig. A. Using an AC voltmeter to check AC leakage.

SAFETY-RELATED COMPONENT WARNING !! COMPONENTS IDENTIFIED BY MARK ! OR DOTTED LINE WITH MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTSPUBLISHED BY SONY.

ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ!! LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE ! SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.

–3–

MODEL IDENTIFICATION — BACKPANEL — MODEL DR4: E, AR model DR4: TH model DR4: SP model DR4: MX model DR4: AUS model DR4: EA model DR5: E, AR model DR5: SP model DR5: MX model DR440: MX model W300: US model W300: CND model W5000: US model DR6: E, AR model DR6: MX model XB500: AEP, UK model XB500: AEP model
• Abbreviation CND : Canadian model TH : Thailand model SP : Singapore model MX : Mexican model AUS : Australian model EA...