Impresora Termica

USER’S GUIDE

Thermal Printer

DPU-414

Read this manual carefully before using the printer. Keep this manual in a place where it can be accessed quickly.

Seiko Instruments Inc.

DPU-414 THERMAL PRINTER USER’S GUIDE Document Number U00112267103 First Edition October 1996 Second Edition September 1997 Third Edition December 1998 Fourth Edition July 2000 Fifth Edition May 2001 SixthEdition June 2003 Seventh Edition September 2004 Eighth Edition February 2006 Ninth Edition April 2006 Tenth Edition February 2007 Eleventh Edition September 2007 Twelfth Edition July 2008 Thirteenth Edition August 2008 Fourteenth Edition July 2009 Fifteenth Edition October 2009 Copyright 1996, 1997, 1998, 2000, 2001, 2003, 2004, 2006, 2007, 2008, 2009 by Seiko Instruments Inc. All rights reserved.Seiko Instruments Inc. (SII) has prepared this manual for use by SII personnel, licensees, and customers. The information contained herein is the property of SII and shall not be reproduced in whole or in part without the prior written approval of SII. SII reserves the right to make changes without notice to the specifications and materials contained herein and shall not be responsible for anydamages (including consequential) caused by reliance on the materials presented, including but not limited to typographical, arithmetic, or listing errors.
is a trademark of Seiko Instruments Inc.

This product complies with EU RoHS Directive(2002/95/EC). Please refer to the page in Chinese for the information of the hazardous substances under China RoHS (Management Methods for ControllingPollution by Electronic Information Products). For use in Turkey Complies with Electrical and Electronic Equipment Directive. Türkiye’ deki Kullanıcılar için EEE Yönetmeliğine Uygundur.

Applicable EC Directives & standards: Directives 2004/108/EC 2006/95/EC EC Electromagnetic Compatibility Directive EC Low Voltage Directive

Standards EMI: EN55022 Class B EN61000-3-2 EN61000-3-3 EMS: EN55024EN61000-4-2, EN61000-4-3, EN61000-4-4, EN61000-4-5, EN61000-4-6, EN61000-4-8, EN61000-4-11 LVD: EN60065

Federal Communications Commission (FCC) compliance statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in aresidential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which canbe determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or anexperienced radio/TV technician for help. Any changes in this certified device could void your legal right to operate it.

Industry Canada (IC) compliance statement Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

INTRODUCTIONThank you for purchasing the DPU-414 thermal printer. This USER’S GUIDE explains how to handle DPU-414 thermal printer (hereinafter referred to as printer), specified AC adapter, specified battery pack and specified AC cable (hereinafter, omit “specified”). This USER’S GUIDE applies to the following product. ・DPU-414-30B-E Read through the Safety Precautions on Page 2 to 6 carefully before using...