Informatica

Reference Guide

AOS-W 6.1
Command Line Interface

Copyright
© 2011 Alcatel-Lucent. All rights reserved.
Specifications in this manual are subject to change without notice.
Originated in the USA.
AOS-W, Alcatel 4302, Alcatel 4304, Alcatel 4306, Alcatel 4308, Alcatel 4324, Alcatel 4504, Alcatel 4604, Alcatel 4704, Alcatel 6000,
OAW-AP41, OAW-AP68, OAW-AP60/61/65, OAW-AP70, OAW-AP80,OAW-AP92/93, OAW-AP105, OAW-AP120/121, OAW-AP124/
125, OAW-AP175, OAW-IAP92/93/105, OAW-RAP2, OAW-RAP5, and Omnivista 3600 Air Manager are trademarks of Alcatel-Lucent in
the United States and certain other countries.
Any other trademarks appearing in this manual are the property of their respective companies.

Legal Notice
The use of Alcatel-Lucent switching platforms and software, by allindividuals or corporations, to terminate Cisco or Nortel VPN client
devices constitutes complete acceptance of liability by that individual or corporation for this action and indemnifies, in full, AlcatelLucent from any and all legal actions that might be taken against it with respect to infringement of copyright on behalf of Cisco Systems
or Nortel Networks.

www.alcatel-lucent.com
26801 WestAgoura Road
Calabasas, CA 91301

AOS-W 6.1 Command Line Interface | Reference Guide

0510840-01 | June 2011

Introduction

The AOS-W command line interface (CLI) allows you to configure and manage your switches. The CLI
is accessible from a local console connected to the serial port on the switches or through a Telnet or
Secure Shell (SSH) session from a remote management console orworkstation.
Telnet access is disabled by default. To enable Telnet access, enter the telnet cli command from a serial
connection or an SSH session, or in the WebUI navigate to the Configuration > Management > General
page.

What’s New In AOS-W 6.1
The following commands have been added in the AOS-W 6.1 command line interface.
Command

Description

clear wms wired-mac

Clear learned andcollected Wired MAC information.

cluster-member-customcert

This command sets the switch as a control plane security cluster root, and
specifies a custom user-installed certificate for authenticating cluster
members

cluster-member-factorycert

This command sets the switch as a control plane security cluster root, and
specifies a custom user-installed certificate for authenticatingcluster
members.

controller-ipv6

This command sets the default IPv6 address of the switch to the IPv6
loopback interface address or a specific VLAN interface address.

crypto-local ipsec sacleanup

Issue this command to clean IPsec security associations (SAs).

crypto-local isakmp
certificate-group

Issue this command to configure an IKE Certificate Group for VPN clients.crypto-local isakmp sacleanup

This command enables the cleanup of IKE SAs.

crypto-local isakmp xauth This command assigns the server certificate used to authenticate the
switch for VPN clients using IKEv2.
ip igmp

Added parameters: max-members-per-group and quick-clientconver

interface vlan ipv6
address

This command configures the link local address or the global unicast
adress for thisinterface.

ipv6 cp-redirect-address

This command configures a redirect address for captive portal.

ipv6 default-gateway

This command configures an IPv6 default gateway.

ipv6 mld

This command configures the IPv6 MLD(Multi-listener discovery)
parameters.

ipv6 neighbor

This command configures an IPv6 static neighbor on a VLAN interface.

ipv6 route

This commandconfigures static IPv6 routes on the switch.

AOS-W 6.1 Command Line Interface | Reference Guide

Introduction | 3

Command

Description

local-custom-cert

This command configures the user-installed certificate for secure
communication between a local switch and a master switch.

local-factory-cert

This command configures the factory-installed certificate for secure
communication...