Ingeniero
Páginas: 3 (559 palabras)
Publicado: 20 de agosto de 2012
WWW.PHIHONG.COM
30W Power Over Ethernet Adapter High Power single port injector.
Features
• • • • • • • • • • Fully Compliant detection, disconnect and voltage control IEEE802.3af DiagnosticLEDs Non-Vented Case
• • • • •
UNH IOL Tested Full Protection OCP, OVP Gigabit Compatible
Applications
IP Telephones Wireless Network Access Points Blue Tooth Access Point
Security CameraIP Print Servers
Safety Approvals
cUL/UL CE
•
TUV
Mechanical Characteristics
Length: 140mm (5.51in) Width: 65mm (2.55in)
• •
Height: 36mm (1.42in) Weight: 0.2Kg (0.44lb.)
OutputSpecifications Model
POE30U-560
DC Output Voltage
56V 0A
Load Min. Max.
0.55A
Regulation Line Load
54-57Vdc under all conditions
Ripple And Noise* 10M OHM 500VDC Primary to FC: >10MOHM 500VDC
DC Offset
No Data degradation with DC imbalance 18mA
FEATURE:
Over Voltage/Current, Short Circuit Protection
Outputs equipped with short circuit protection and overload protectionas per 802.3af specification except max average current is 0.55A, Peak 0.6A The output can be shorted permanently without damage
Efficiency
65% (typical) at Max. load, and 120VAC 60Hz
Hold-upTime
16mS min. 120VAC and max. load
Indicators
Led #1 indicator for input power “on” GREEN Led #2 Indicator for fault-RED Led #3 Indicator that Detected and Connected to valid IEEE802.3afload-GREEN
Transient O/P Voltage Protection
60V max.
ENVIRONMENTAL:
Temperature
Operation Non-operation 0 to +40°C -25 to +65°C
Input Connector
IEC320 inlet 3 pin
Humidity
Operation 5 to 90%Output Connection +pins 3,6 - pins 1,2
Dimension Diagram Unit: mm (inch)
Gigabit Power Injector Block Diagram
Power-up Sequence:
Description of LED Functions for Gigabit PowerInjector
Upon power-up, all 3 LEDs will light for 2 seconds, as part of the self-test for the internal microprocessor software. After the end of the 2 seconds, the "ON" LED will illuminate green,...
30W Power Over Ethernet Adapter High Power single port injector.
Features
• • • • • • • • • • Fully Compliant detection, disconnect and voltage control IEEE802.3af DiagnosticLEDs Non-Vented Case
• • • • •
UNH IOL Tested Full Protection OCP, OVP Gigabit Compatible
Applications
IP Telephones Wireless Network Access Points Blue Tooth Access Point
Security CameraIP Print Servers
Safety Approvals
cUL/UL CE
•
TUV
Mechanical Characteristics
Length: 140mm (5.51in) Width: 65mm (2.55in)
• •
Height: 36mm (1.42in) Weight: 0.2Kg (0.44lb.)
OutputSpecifications Model
POE30U-560
DC Output Voltage
56V 0A
Load Min. Max.
0.55A
Regulation Line Load
54-57Vdc under all conditions
Ripple And Noise* 10M OHM 500VDC Primary to FC: >10MOHM 500VDC
DC Offset
No Data degradation with DC imbalance 18mA
FEATURE:
Over Voltage/Current, Short Circuit Protection
Outputs equipped with short circuit protection and overload protectionas per 802.3af specification except max average current is 0.55A, Peak 0.6A The output can be shorted permanently without damage
Efficiency
65% (typical) at Max. load, and 120VAC 60Hz
Hold-upTime
16mS min. 120VAC and max. load
Indicators
Led #1 indicator for input power “on” GREEN Led #2 Indicator for fault-RED Led #3 Indicator that Detected and Connected to valid IEEE802.3afload-GREEN
Transient O/P Voltage Protection
60V max.
ENVIRONMENTAL:
Temperature
Operation Non-operation 0 to +40°C -25 to +65°C
Input Connector
IEC320 inlet 3 pin
Humidity
Operation 5 to 90%Output Connection +pins 3,6 - pins 1,2
Dimension Diagram Unit: mm (inch)
Gigabit Power Injector Block Diagram
Power-up Sequence:
Description of LED Functions for Gigabit PowerInjector
Upon power-up, all 3 LEDs will light for 2 seconds, as part of the self-test for the internal microprocessor software. After the end of the 2 seconds, the "ON" LED will illuminate green,...
Leer documento completo
Regístrate para leer el documento completo.