Instalacion Aficio 3030
REV IS ION H IST ORY
Pag e 70 ~ 73 72 Date 06/22/2006 11/11/2005 Ad d ed / Up d ated / New Updated Information – Data Overwrite Security Unit Updated Information – Data Overwrite Security Unit
INSTALLATION REQUIREMENTS
1.1 INSTALLATION REQUIREMENTS
1.1.1 ENVIRONMENT
1. Temperature Range: 2. Humidity Range: 3. Ambient Illumination: 4. Ventilation: 5. Ambient Dust: 10°C to32°C (50°F to 89.6°F) 15% to 80% RH Less than 1,500 lux (do not expose to direct sunlight.) Room air should turn over at least 30 m3/hr/person Less than 0.10 mg/m3
6. Avoid an area which is exposed to sudden temperature changes. This includes: 1) Areas directly exposed to cool air from an air conditioner. 2) Areas directly exposed to heat from a heater. 7. Do not place the machine in an areawhere it will be exposed to corrosive gases. 8. Do not install the machine at any location over 2,000 m (6,500 ft.) above sea level. 9. Place the copier on a strong and level base. (Inclination on any side should be no more than 5 mm.) 10. Do not place the machine where it may be subjected to strong vibrations.
1.1.2 MACHINE LEVEL
Front to back: Right to left: Within 5 mm (0.2") of level With in5 mm (0.2") of level
SM
1-1
B205/B209/D007/D008
Installation
1. INSTALLATION PROCEDURE
INSTALLATION REQUIREMENTS
1.1.3 MINIMUM SPACE REQUIREMENTS
Place the copier near the power source, providing clearance as shown:
C A: B: C: D: B D In Front: Over 750 mm (29.6") Left: Over 100 mm (0.4") To Rear: Over 100 mm (0.4") Right: Over 100 mm (0.4")
A
E F G E: F: G: H: H 620mm (24.4") 640 mm (25.2") 550 mm (21.7") 1137 mm (44.8")
NOTE: The 750 mm recommended for the space at the front is only for pulling out the paper tray. If an operator stands at the front of the copier, more space is required.
B205/B209/D007/D008
1-2
SM
INSTALLATION REQUIREMENTS
CAUTION
1. Make sure that the wall outlet is near the copier and easily accessible. Make sure theplug is firmly inserted in the outlet. 2. Avoid multi-wiring. 3. Be sure to ground the machine. 1. Input voltage level: 120 V, 60 Hz: More than 12 A 220 V ~ 240 V, 50 Hz/60 Hz: More than 7 A 110V, 50 Hz/60 Hz: More than 13 A 2. Permissible voltage fluctuation: ±10 % 3. Do not set anything on the power cord.
SM
1-3
B205/B209/D007/D008
Installation
1.1.4 POWER REQUIREMENTS
COPIERINSTALLATION
1.2 COPIER INSTALLATION
1.2.1 POWER SOCKETS FOR PERIPHERALS
CAUTION
Rating voltage for peripherals. Make sure to plug the cables into the correct sockets.
1. ADF 1. Rating voltage output connector for accessory Max. DC24 V 2. Bridge Unit or Shift Tray 1. Rating voltage output connector for accessory Max. DC24 V
3. Duplex Unit 1. Rating voltage output connector foraccessory Max. DC24 V
4. By-pass Tray 1. Rating voltage output connector for accessory Max. DC24 V
B205/B209/D007/D008
1-4
SM
INSTALLATION REQUIREMENTS
The following flow chart shows how to install the optional units more efficiently.
Unpack the copier
Does the user require the Paper Tray Unit, LCT, or Finisher? Yes Place the copier on the Paper Tray Unit or LCT Install the PaperTray Unit or LCT Install the copier No
Does the user require the Memory Unit? Yes Install the Memory Unit No
Does the user require the By-pass Tray? Yes Install the By-pass Tray No
Does the user require the Shift Tray? Yes Install the Shift Tray No
Does the user require the Finisher? Yes Install the Bridge Unit No
Install the Finisher
Does the user require the Duplex Unit and/or1-bin Tray Unit ? Yes Install the Interchange Unit No
Install the Duplex Unit and/or 1-bin Tray Unit
Install the ARDF or Platen Cover (if required)
SM
1-5
B205/B209/D007/D008
Installation
1.2.2 INSTALLATION FLOW CHART
COPIER INSTALLATION
1.2.3 ACCESSORY CHECK
Check the quantity and condition of the accessories in the box against the following list: Description Q'ty...
Regístrate para leer el documento completo.