Assessment System Skip to Time Left | Skip to Navigation | Skip to Assessment Items
Take Assessment - DRSEnt Final - CCNA Discovery (Version 4.0) Time Remaining: Showing 1 of 4 Next> Page: Introduction 1 2 3 4 Submit GO R3 will be installed in the routing table. If OSPF and RIPv2 are both configured on the network, OSPF paths will be installed in the routing table. If EIGRP and OSPF are bothconfigured on the network, EIGRP paths will be installed in the routing table. If EIGRP and RIPv2 are both configured on the network, RIPv2 paths will be installed in the routing table. If RIPv2 is the routing protocol, the two equal cost paths (R1-R2-R3 and R1-R4R3) will be installed in the routing table.
10 Refer to the exhibit. None of the hosts in network A are able to access the Internet.How can this problem be resolved? Configure dynamic NAT instead of PAT. Configure the access list for the correct network. Include the ip nat pool command in the configuration. Configure the ip nat inside command on the correct interface.
11 Refer to the exhibit. Which VTP function will this switch perform? It the It It It will create, XYZ domain. will forward will back up will forward changeand share local VLAN information with other switches in to other switches the VLANs that are created in Switch1. the VTP database for domain XYZ. VTP configuration information for domain XYZ.
12 Refer to the exhibit. The network administrator wants to restrict the Production network from accessing the HR network. All other traffic will have access to all networks. Which combination of interfaceand direction should the administrator use to apply the ACL? Fa0/1, out
Fa1/0, out Fa0/1, in Fa1/0, in
13 Refer to the exhibit. R1 is using the default OSPF operation. Which IP address will be used as the router ID of R1? 192.168.201.1 172.16.1.1 10.10.10.1 10.1.1.1
14 What is an advantage of using a default route? They They They They never fail. reduce the size of the routing table.prevent routing loops between the edge router and the ISP. transfer traffic from the Internet to the network.
15 Which three statements correctly describe the features of IEEE STP? (Choose three.) It reconfigures port states if a link failure is detected. It provides a mechanism for disabling redundant links in a switched network. It immediately transitions all ports that are not discarding to theforwarding state. It has three port states: discarding, learning, and forwarding. It ensures that there are no loops in the switched network. It converges the switched network in less than 1 second.
16 Refer to the exhibit. A network administrator must manually summarize all IP addresses on the POP router for the ISP. Which one is the correct summary address? 192.168.0.0/22 192.168.0.0/23192.168.0.0/24 192.168.0.0/25
17 Refer to the exhibit. The network administrator has used classless routing in the network. What is the result of running the displayed command? All packets serial0/0/0. All packets serial0/0/0. All packets serial0/0/0. All packets serial0/0/0. that are destined for address 10.12.0.1/22 will be forwarded via that are destined for address 10.12.14.0/22 will beforwarded via that are destined for address 10.12.16.1/22 will be forwarded via that are destined for address 10.12.15.255/22 will be forwarded via
18 Refer to the exhibit. R1 and R2 are connected via serial interfaces. Both interfaces show that there is Layer 2 connectivity between them. The administrator verifies that CDP is operational; however, pings between the two interfaces are unsuccessful.What is the cause of this connectivity problem? no set loopback incorrect subnet mask on R2 incompatible bandwidth incorrect IP address on R1 incompatible encapsulation
19 What are two benefits of implementing VLANs in an enterprise network? (Choose two.) eliminates the need for a Layer 3 device provides segmentation of broadcast domains allows for the propagation of broadcasts from one local...
Leer documento completo
Regístrate para leer el documento completo.