Listado Normas Iec

The fol lowing r efer enced documents ar e indispensab le f or the appl icat ion of th is document .
For dated refer ences , only the ed i tion ci ted applies. For undated ref erences, the lates t ed i t ion
of the referenced document (including any amendments) applies.
IEC 60300- 3-1:2003, Dependabi l ity managemen t – Par t 3-1: Appl icat ion gu ide – Analys istechniques for dependabi l ity – Guide on methodology
IEC 61025, Faul t tree analysis (FTA)
IEC 61078, Analys is techniques for dependabi l ity – Re l iabi l ity block diagram method

IEC 60050-191:1990, International Electrotechnical Vocabulary. Chapter 191: Dependability and
quality of service
[2] IEC 60079 (all parts), Electrical apparatus for explosive gas atmospheres[3] IEC 60300-1, Dependability management — Part 1: Dependability management systems
[4] IEC 60300-2, Dependability management — Part 2: Guidelines for dependability management
[5] IEC 60300-3-1, Dependability management — Part 3: Application guide — Analysis techniques for
dependability — Guide on methodology
[6] IEC 60300-3-2, Dependability management — Part 3: Application guide —Collection of dependability
data from the field
[7] IEC 60300-3-3, Dependability management — Part 3: Application guide — Life cycle costing
[8] IEC 60300-3-4, Dependability management — Part 3: Application guide — Section 4: Guide to the
specification of dependability requirements
[9] IEC 60300-3-5, Dependability management — Part 3-5: Application guide — Reliability test conditions
andstatistical test principles
[10] IEC 60300-3-6, Dependability management — Part 3: Application guide — Section 6: Software
aspects of dependability
[11] IEC 60300-3-7, Dependability management — Part 3-7: Application guide — Reliability stress
screening of electronic hardware
[12] IEC 60300-3-9, Dependability management — Part 3: Application guide — Section 9: Risk analysis of
technologicalsystems
[13] IEC 60300-3-10, Dependability management — Part 3-10: Application guide — Maintainability
[14] IEC 60300-3-11, Dependability management — Part 3-11: Application guide — Reliability centred
maintenance
[15] IEC 60300-3-12, Dependability management — Part 3-12: Application guide — Integrated logistic
support
[16] IEC 60319, Presentation and specification of reliability data forelectronic components
[17] IEC 60381-2, Analog signals for process control systems — Part 2: Direct voltage signals
[18] IEC 60605-4, Equipment reliability testing — Part 4: Statistical procedures for exponential
distribution — Point estimates, confidence intervals, prediction intervals and tolerance intervals
[19] IEC 60605-6, Equipment reliability testing — Part 6: Test for the validity of theconstant failure rate or
constant failure intensity assumptions
[20] IEC 60706-1, Guide on maintainability of equipment — Part 1: Introduction, requirements and
maintainability programme
EN ISO 14224:2006
Copyright British Standards Institution
Provided by IHS under license with BSI - Uncontrolled Copy Licensee=BP International/5928366101
Not for Resale, 06/28/2009 22:35:24 MDT Noreproduction or networking permitted without license from IHS
--`,`,``,,`,```,```````,````,`,-`-`,,`,,`,`,,`---
169
[21] IEC 60706-2, Guide on maintainability of equipment — Part 2: Maintainability studies during the design
phase
[22] IEC 60706-3, Guide on maintainability of equipment — Part 3: Verification and collection, analysis and
presentation of data
[23] IEC 60706-4, Guide onmaintainability of equipment — Part 4: Maintenance and maintenance support
planning
[24] IEC 60706-5, Guide on maintainability of equipment — Part 5: Diagnostic testing
[25] IEC 60706-6, Guide on maintainability of equipment — Part 6: Statistical methods in maintainability
evaluation
[26] IEC 60812, Analysis techniques for system reliability — Procedure for failure mode and effects
analysis (FMEA)...