Manual Autoclave

Go To Table Of Contents

UltraClave Automatic Sterilizers
Model Numbers:

®

M9 M9D M11 M11D

Serial Number Prefixes:
RN, RP, RR, V

-020 thru -022 -020 & -022

Service and Parts Manual

RW, RX, V

-020 thru -022 -020 & -022

RS, RT, RV, V

RY, RZ, V

To search for a specific error code, click on the button below then type in error code. [ex. Cxxx]

To purchase aprinted copy of this manual, click on the "Place Order" button below.

Find Error Code

Place Order

FOR USE BY MIDMARK TRAINED TECHNICIANS ONLY
SF-1854 Part No. 004-0453-00 Rev. E (4/1/08)

Back

Next

General Information

Table Of Contents

Section C Section D Section E Section E

Symbols .................................... i Ordering Parts .......................... i Model /Serial Number Location .................................. i Weights, Dimensions, Electrical Specifications ....... ii Model Identification / Compliance Chart .................. iii Cycle Parameters ..................... iv Special Tools ............................ iv Warranty Information ............... v

Section B

GENERAL INFORMATION

TESTING & REPAIR - continued
Door Motor System.................. B-39 Fan & Fan Thermostat ............. B-42 Main PC Board ......................... B-46 Printer (optional) ....................... B-50 Adjusting the Dry Time ............ B-53

ACCESS PROCEDURES
Removing & Installing: Covers / Panels ........................ C-2 Tray Plate / Rack ...................... C-3 Draining / Filling Reservoir ..... C-4

Section A

OPERATION &TROUBLESHOOTING
Error Codes .............................. A-2 Power-Up Mode ........................ A-18 Fill Mode ................................... A-20 Heat-Up Mode ........................... A-22 Sterilization Mode .................... A-24 Vent Mode ................................. A-26 Door Motor System .................. A-28 Drying Mode ............................. A-30 Fan System............................... A-32 PC-Based Diagnostic Program .................................. A-34

WIRING & FLOW DIAGRAMS
M9 (-020 / -021 / -022):
Wiring Diagram ............................. D-2 Flow Diagram ............................... D-4

M9D (-020 / -022):
Wiring Diagram ............................. D-3 Flow Diagram ............................... D-4

M11 (-020 / -021 /-022):
Wiring Diagram ............................ D-2 Flow Diagram .............................. D-4

TESTING & REPAIR

M11D (-020 / -022): Wiring Diagram ............................ D-3 Checking for Pressure Leaks ...................... B-2 Flow Diagram .............................. D-4 Using a Pressure Gauge ......... B-3 Fuses ......................................... B-4 ServiceDiagnostics ................. B-5 EXPLODED VIEWS / PARTS LISTS Air Valve .................................... B-12 M9 (-020 / -021 / -022) ............... E-2 Fill & Vent Valves ...................... B-15 M9D (-020 / -022): ..................... E-3 Pressure Relief Valve ............... B-18 M11 (-020 / -021 / -022) ............. E-2 Heating Element ....................... B-20 M11D (-020 / -022):................... E-3 Tempreature Sensor ................ B-23 Water Level Sensor .................. B-27 High-Limit Thermostats ........... B-31 Door Switch .............................. B-34 MIDMARK TRAINED TECHNICIANS ONLY FOR USE BY Touch Pad & Display Panel ..... B-37

Section B

Back

Go To Table Of Contents

Next

General Information

Symbols
Caution
Indicates a potentiallyhazardous situation which could result in injury if not avoided.

Ordering Parts

General Information

Equipment Alert
Indicates a potentially hazardous situation which could result in equipment damage if not avoided.

The following information is required when ordering parts: • Serial number & model number • Part number for desired part. [Refer to Section E: Exploded Views / Parts Lists]...