Manual Buffalo

User Manual for Professional Firmware WZR-HP-AG300H
Nfiniti High Power Wireless Router & Access Point

www.buffalotech.com
35011803 ver.01

Introduction 1. 1.1. Welcome 1.2. Device Configuration 1.2.1. Factory Settings 1.2.2. Initial Operation 2. Configuration via the Web Interface 2.1. Preparation 2.2. Web Interface Access 2.3. Web Interface Structure 2.3.1. Setup 2.3.1.1. BasicConfiguration 2.3.1.2. Dynamic DNS (DynDNS or DDNS) 2.3.1.3. MAC Address Cloning 2.3.1.4. Advanced Routing 2.3.1.5. Networking 2.3.1.6. EoIP Tunnel 2.3.2. Wireless 2.3.2.1. Basic Settings 2.3.2.2. Wireless Security 2.3.2.3. AOSS/WPS 2.3.2.4. MAC Filter 2.3.3. Services 2.3.3.1. Services 2.3.3.2. FreeRadius 2.3.3.3. PPPoE Server 2.3.3.4. VPN 2.3.3.5. USB 2.3.3.6. NAS 2.3.3.7. Hotspot 2.3.3.8. Milkfish SIPRouter 2.3.3.9. My Ad Network 2.3.4. Security 2.3.4.1. Firewall 2.3.4.2. VPN Pass-through 2.3.5. Access Restrictions 2.3.5.1. WAN Access 2.3.6. NAT / QoS 2.3.6.1. Port Forwarding 2.3.6.2. Port Range Forwarding 2.3.6.3. Port Triggering 2.3.6.4. UPnP 2.3.6.5. DMZ 2.3.6.6. QoS 2.3.7. Administration 2.3.7.1. Management 2.3.7.2. Keep Alive 2.3.7.3. Commands 2.3.7.4. WOL 2.3.7.5. Factory Defaults 2.3.7.6.Firmware Upgrade 2.3.7.7. Backup 2.3.8. Status 2.3.8.1. Router 2.3.8.2. WAN 2.3.8.3. LAN 2.3.8.4. Wireless 2.3.8.5. Bandwidth -1-

3 3 3 3 3 4 4 4 5 6 6 6 7 7 7 8 8 8 10 11 12 12 12 12 13 13 13 13 14 14 14 14 14 14 14 14 14 14 15 15 15 15 15 15 15 16 16 16 16 16 16 16 16 17 17 17 17

2.3.8.6. SysInfo 3. Use Cases 3.1. Access Point 3.1.1. Access Point with NAT / DHCP 3.1.1. Access Pointattached to a network / Internet gateway 3.2. Wireless Client 3.3. Wireless Client Bridge 3.4. FTP Server 3.4.1. Examples 3.4.2. Logging into the FTP server 3.4.3. Common FTP commands 4. GPL Statement 4.1. GNU General Public License 4.1.1. Preamble 4.1.2. GNU General Public License – Terms and Conditions or Copying, Distribution and Modification 4.1.3. NO WARRANTY Appendix Product Warranty Information17 18 18 18 19 20 21 23 23 25 25 27 27 27 28 31 33

-2-

1. Introduction
1.1. Welcome
This AirStation wireless router comes with two different firmware packages. You may use either the dd-wrt-based Professional firmware or the simple User-friendly firmware. By default, the Professional firmware is preinstalled for US/EU products, and the User-friendly firmware is preinstalled forAsia-Pacific products.

1.2. Device Configuration
From the factory, the router is configured as a network bridge. That means that all network interfaces can communicate with each other using this default bridge. The router is ready to use with a few simple adjustments.

1.2.1.

Factory Settings

Because all interfaces are attached to the bridge by default, they all have the same IPconfiguration: IP address Subnet Mask DHCP server DHCP-Range 192.168.11.1 255.255.255.0 enabled 192.168.11.2 - 66

The Wireless LAN interface is activated by default with an SSID generated from the device’s MAC address. For security, unused interfaces should be disabled. Wireless LAN interfaces that are not disabled should be configured with secure encryption (WPA2 or WPA is recommended) and a securepassword.

1.2.2.

Initial Operation

Connect your computer to the router with an Ethernet LAN cable and power the router on. It will take about 30 seconds to boot. You can then access it via telnet or web browser at the IP address 192.168.11.1. The DHCP server in the router is enabled by default. If your PC’s Ethernet is configured for DHCP it should receive an IP address from the router’s DHCPserver. If not, please configure the Ethernet interface with an address from the 192.168.11.x subnet. Because all relevant settings can be made using the web interface, this manual refers to configuration via the web GUI only.

-3-

2.

Configuration via the Web Interface
The router contains an integrated web server that provides an easy to use web interface. It allows configuration,...