Manual centrifuga decantadora

5500 CENTRISMART ™ OPERATIONS MANUAL
Revised April 2004

3520 East Belt Houston, Texas 77015 (713) 455 – 9600 ● Fax: (713) 455 – 7753 (800) 441 – 4850 www.hutch-hayes.com

1

Hutchison Hayes, L. P.

NOTICE OF CONFIDENTIALITY This information is highly confidential and is solely for the benefit of Recipient

2

TABLE OF CONTENTS 5500 CENTRISMART ™ OPERATIONS MANUAL
SECTION 1 -INTRODUCTION Overview Data SECTION 2 -START-UP Safety Installation Pre Start – Safety Precautions Belt Tension Procedure Variable Main/Back Drive…See Section 13 Hydraulic Back Drive SECTION 3 - OPERATION A. Variable Main & Back Drive Hydraulic Back Drive Standard Warning Torque Lever & Setting B. Cleaning C. Dam Plate Adjustment Pond Depth Chart SECTION 4 - LUBRICATION A. Grease & Oil Data LubricationSchedule SECTION 5 - ASSEMBLY & DISASSEMBLY A. Gearbox Removal B. Rotating Assembly Removal C. Conveyor Removal 1. Conveyor Disassembly D. Pillow Block Disassembly E. Front Bowl Hub F. Rear Bowl Hub G. Assembly & Disassembly Tips H. Recommended Capscrew Seating Torque I. Conveyor, Wear Protection 27 Page 5

9

22

33

3

Page SECTION 6 - PLANETARY GEARBOX & BACK DRIVE ASSEMBLY SECTION7 - PARTS LIST Base Unit Electric Variable Back Drive Electric Variable Main Drive Hydraulic Back Drive Standard SECTION 8 - ELECTRICAL & WIRING Electric Variable Main & Back Drive Hydraulic Back Drive Standard SECTION 9 - TROUBLE SHOOTING Electric Variable Main & Back Drive…See Section 13 Hydraulic Back Drive Standard SECTION 10 – ELEVATION, DIMENSIONS & WEIGHTS Electric Variable Main & BackDrive Hydraulic Back Drive Standard SECTION 11 - MISCELLANEOUS Recommended spare parts list Electric Variable Main & Back Drive Hydraulic Back Drive Standard Charts Storage SECTION 12 - VENDOR DATA - SECTION 12 SECTION 13 - SUPPLEMENT- SYSTEM OPERATION 58 67

78

97

100

106

113 145

4

SECTION I INTRODUCTION

5

OVERVIEW
HUTCHISON HAYES HIGH “G” CENTRIFUGE MODEL 5500

ThisService Manual describes the centrifuge, and lists instructions for the installation, operation, and maintenance requirements. The basic purpose of this centrifuge is to separate the liquid and solids from the fluid feed (slurry.) A stainless steel rotating bowl, driven by a 60 H.P. electric motor is used to centrifuge the slurry; that is to sling the solids against its inside wall surface while astainless steel screw conveyor (faced with hard tiles) gathers and conveys these solids to a central discharge area. The conveyor is driven at a slightly slower RPM through a planetary gear reducer. The liquids migrate to the front end of the machine and are dispelled through four (4) adjustable plate dam openings, to a central discharge area. For a more comprehensive description of how thecentrifuge operates, see the Operation Section of this manual.

6

5500 INDUSTRIAL MODEL CENTRIFUGE DATA Normal Bowl Centrifugal Force: Normal Bowl Operating Speed: Normal Conveyor Operating Speed: Max. Bowl Centrifugal Force: Max. Bowl Operating Speed: Max. Conveyor Operating Speed: GB-100 Gear Unit Max. Output Shaft Torque: Max. Pinion Shaft Torque: Ratio: Differential Speed: Motor Speed: MotorSheave: Centrifuge Sheave: Rated Solids Output: Bowl Inside Diameter: Bowl Length: Package Weight Empty: (Floormount Unit) OILFIELD MODEL (SKID MOUNTED) Normal Bowl Centrifugal Force: Normal Bowl Operating Speed: Normal Conveyor Operating Speed: Max. Bowl Centrifugal Force: Max. Bowl Operating Speed: Max. Conveyor Operating Speed: GB-53 Gear Unit Max. Output Shaft Torque: Max. Pinion Shaft Torque:Ratio: Differential Speed: Bowl Dimensions: Package Weight Empty: 2118 G’s 3053 RPM 2996 RPM 3110 G’s 3700 RPM 3630 RPM 2118 G’s 3053 RPM 3022 RPM 3110 G’s 3700 RPM 3663 RPM

36,000 LB. IN. 363.6 LB. IN. 99.28 :1 31 RPM 1750 RPM 14” O.D. 8.025” O.D. 12,000 LBS./HR. 35.500 (MAX.) 16 IN. 55.56 IN. 7,365 LBS.

(Approx.)

36,000 LB. IN. 679 LB. IN. 53 :1 57 RPM Same as Above 8,000 LBS.

7...