Manual De Humidificador

Bulletin 539-A

HumidiClean™
Series HC- 6100/6300/6500/6700
Humidifiers
Installation, Operation and
Maintenance Instructions

Table of Contents
Page
Warning Labels
Description of Model Number
Installation
Display Menu
Start-Up Procedure and Operation
Maintenance
Troubleshooting
Typical Wiring Schematic
Repair Parts
Software Update
Communication
Warranty

Please read andsave these instructions.

2-3
4
6-12
13-16
16-17
18-22
22-27
28-37
36-42
43-46
46-51
52

The Armstrong HumidiClean humidifier converts ordinary tap water or purified water to steam
for distribution to raise the relative humidity level.
To allow HumidiClean to function to its full capability, be certain to install in accordance with
Armstrong recommendations.
DANGER: ELECTRICALSHOCK HAZARD HIGH VOLTAGES EXIST INSIDE THE HUMIDIFIER
TO PROTECT YOURSELF AND OTHERS FROM ACCIDENTAL SHOCKS:
1.

Keep the humidifier locked during normal operation and store the key in a safe location away
from the humidifier.

2.

ALWAYS DISCONNECT THE POWER SUPPLY AT THE CIRCUIT BREAKER OR SAFETY
SWITCH BEFORE OPENING ANY COVERS AND DOORS!

3.

Before servicing the humidifier, learnwhere the high voltage parts are. KEEP HANDS AND
METAL TOOLS AWAY FROM THESE AREAS!

Model HC-6100/HC-63000 Series

Model HC-6500/HC-67000 Series

Warning: All wiring and installation must be completed by qualified personnel
only and per the relevant local or national codes on electrical wiring. Negligence
of this warning might result in the loss of property or personal damage.
6010-ISOElectrical
Shock-Electrocution

Warning: High Temperature! Material that is not resistant to high temperature
should not come in contact with these areas. Negligence of this warning might
result in the loss of property or personal damage.
6043-ISO Burn Hazard
Hot Surface

2

Warning: Do not operate the supplied humidifier in combustible or explosive surroundings.
Warning: Do notoperate the supplied humidifier if there is any damage to the cabinet or any
components in humidifier are damaged.
Warning: The main switch should be a connection breaker which has over current and leakage
current protecting functions per code EN60947-3 or EN60947-2 if point gap required by EN60947-3
can be fulfilled.
4. Physical environment and operating conditions
• Ambient temperature + 4°C ~+ 38°C (40°F to 100°F)
• Humidity = 50 % at 40°C (104°F), = 90 % at 20°C (68°F)
• Altitude = 1000 m (above mean sea level) (3300 ft)
5. Transportation and storage conditions
Electrical equipment shall be designed to withstand, or suitable precautions shall be taken to
protect against, the effects of transportation and storage temperatures within a range of
-25°C to + 55°C (-15°F to 130°F)and for short periods not exceeding 24h, up to +70°C (160°F).
Suitable means shall be provided to prevent damage from humidity, vibration and shock.
6. Requirements
The supply disconnecting device (i.e. a switch-disconnect, a disconnect used in combination with
switching devices, or a circuit-breaker) shall fulfill all of the following requirements:
• Isolate the electrical equipment from thesupply and have one OFF (isolated) and one ON
position only, clearly marked with "O" and "I" (symbols 60417-2-IEC-5008 and
60417-2-IEC-5007, see 10.2.2), with the actuating directions in accordance with IEC60447.
Circuit-breaker that, in addition, has a reset (tripped) position between "O" and "I" are also
deemed to satisfy this requirement
• Have a visible gap or a position indicator whichcannot indicate OFF (isolated) until all contacts
are actually open and there is an adequate isolating distance between all the contacts in
accordance with IEC 60947-3
• Have an external operating means (e.g. handle), (exception: power-operated switchgear need
not be operable from outside the enclosure where there are other means to open it). The
handle should be BLACK or GREY (exception: see...