Manual De Impresora Al-1631

MODEL

AL-1631
AL-1641CS
DIGITAL LASER COPIER
DIGITAL MULTIFUNCTIONAL
SYSTEM
OPERATION MANUAL
Page

INTRODUCTION

4

SETTING UP THE UNIT

7

LOADING PAPER
INSTALLING THE
SOFTWARE (AL-1641CS)
MAKING COPIES
SPECIAL FUNCTIONS

IN CHINA
KS 1
3J
E1161QSZZ

19
46

MAINTENANCE

AL-1631/AL-1641CS

14

57

TROUBLESHOOTING
THE UNIT
APPENDIX

61

52

68FOR YOUR PROTECTION...
To aid in reporting this unit in case of loss or theft, please record below the model number
and serial number located on the back of the unit. We also suggest you record all the
information listed and retain for future reference.
MODEL NUMBER

SERIAL NUMBER

DATE OF PURCHASE
Dealer
Address

City

State

Zip

Telephone

Service Station
Address

CityState

Zip

Telephone

To obtain service, or to obtain product literature, accessories, or
supplies,
please call
or

1-(630)378-3590 in the USA
905-568-7140 in Canada.

For customer assistance, please visit http://www.sharpusa.com/
(for USA) or http://www.sharp.ca/ (for Canada) on the World Wide Web
or call 1-(630)378-3590 (for USA).

Do not make copies of anything which isprohibited from copying by law. The
following items are normally prohibited from copying by national law. Other
items may be prohibited by local law.
Money
Stamps
Bonds
Stocks
Bank drafts
Checks
Passports
Driver's licenses

CAUTIONS
Caution label on the unit
The label (
) in the fusing area of the unit indicates the following:
: Caution, risk of danger
: Caution, hot surfaceCautions on using
Follow the cautions below when using this unit.

Warning:
• The fusing area is hot. Exercise care in this area when removing misfed paper.
• Do not look directly at the light source. Doing so may damage your eyes.
• Do not switch the unit rapidly on and off. After turning the unit off, wait 10 to 15
seconds before turning it back on.
• Unit power must be turned off beforeinstalling any supplies.

Caution:
• Place the unit on a firm, level surface.
• Do not install the unit in a humid or dusty location.
• When the unit is not used for a long time, for example for consecutive holidays,
turn the power switch off and remove the power cord from the outlet.
• When moving the unit, be sure to turn the power switch off and remove the power
cord from the outlet.
• Donot cover the unit with a dust cover, cloth or plastic film while the power is on.
Doing so may prevent heat radiation, damaging the unit.
• Use of controls or adjustments or performance of procedures other than those
specified herein may result in hazardous radiation exposure.
• The socket-outlet shall be installed near the unit and shall be easily accessible.

Important points when selectingan installation site
Do not install your unit in areas that are:
• damp, humid, or very dusty
• exposed to direct sunlight
• poorly ventilated
• subject to extreme temperature or humidity changes, e.g., near an air conditioner
or heater.
Be sure to allow the required space around the
8" (20cm)
machine for servicing and proper ventilation.

4"
(10cm)

4"
(10cm)

1

Cautions onhandling
Be careful in handling the unit as follows to maintain the performance of this unit.
Do not drop the unit, subject it to shock or strike it against any object.
Do not expose the drum cartridge to direct sunlight.
• Doing so will damage the surface (green portion) of the drum cartridge, causing
smudges on copies.
Store spare supplies such as drum cartridges and TD cartridges in adark
place without removing from the package before use.
• If they are exposed to direct sunlight, smudges on copies may result.
Do not touch the surface (green portion) of the drum cartridge.
• Doing so will damage the surface of the cartridge, causing smudges on copies.

Trademark acknowledgements
®
®

• Microsoft Windows operating system is a trademark or copyright of Microsoft...