Manual de instalacion

Card Printer Programmer’s Manual

C

A R D

P

R I N T E R

P

R O D U C T S

User’s Manual No. 980081-001
©1999 Zebra Technologies Corporation.

Rev. F

FOREWORD
This manual contains installation and operation information for the Eltron Series card printers manufactured by Zebra Technologies Corporation, Camarillo, California.

RETURN MATERIALS AUTHORIZATION
Beforereturning any equipment to Zebra Technologies Corporation for in-warranty or out-of-warranty repair, contact Repair Administration for a Return Materials Authorization (RMA) number. Repack the equipment in the original packing material and mark the RMA number clearly on the outside. Ship the equipment, freight prepaid, to the address listed below:

For U.S.A and Latin America: Zebra TechnologiesCorporation Eltron Card Printer Products 1001 Flynn Road Camarillo, CA. 93021-8706. U.S.A. Phone: +1 (805) 579-1800 FAX: +1 (805) 579-1808 Toll Free in US: (800) 452 4056 For Europe, Asia, and Pacific: Zebra Technologies Corporation Eltron Card Printer Products Zone Indutrielle, Rue d'Amsterdam 44370 Varades, France Phone: +33 (0) 240 097 070 FAX: +33 (0) 240 834 745

COPYRIGHT NOTICE
This documentcontains information proprietary to Zebra Technologies Corporation. This document and the information contained within is copyrighted by Zebra Technologies Corporation and may not be duplicated in full or in part by any person without written approval from Zebra. While every effort has been made to keep the information contained within current and accurate as of the date of publication, noguarantee is given or implied that the document is error-free or that it is accurate with regard to any specification. Zebra reserves the right to make changes, for the purpose of product improvement, at any time.

TRADEMARKS
Eltron is a trademark of Eltron International Incorporated. Windows and MS-DOS are registered trademarks of Microsoft Corp. All other marks are trademarks or registeredtrademarks of their respective holders.

980081-001 Rev. F

iii

WARRANTY INFORMATION
WE NEED TO HEAR FROM YOU! To Establish Your Warranty Period And Provide Access To Technical Support, Send Us your Product Registration Card Today! Zebra warrants the mechanism, control electronics and power supply, under normal use and service, to be free from defects in material and workmanship for a period oftwelve (12) months from the date of purchase by the end user. Zebra warrants the print head, under normal use and service, to be free from defects in material and workmanship for a period of twelve (12) months or 100k passes (whichever occurs first) from the date of purchase by the end user. Proof of purchase or product registration is required. If proof of purchase or product registration cannotbe established, shipment date to the original buyer (dealer or distributor) will be used to establish the warranty period. Failure to exercise caution to protect the equipment from electrostatic discharge damage, adverse temperature and humidity conditions or physical abuse may void the warranty. Failure to use only Eltron approved media may void the warranty. Zebra will, at its option, repair orreplace the equipment or any parts which are determined to be defective within this warranty period, and which are returned to Zebra F.O.B. factory of origin. The warranty set forth above is exclusive and no other warranty, whether written or oral, is expressed or implied. Zebra specifically disclaims the implied warranties of merchantability and fitness for a particular purpose.

iv980081-001 Rev. F

TABLE OF CONTENTS
INTRODUCTION . . . . . . . . . Features . . . . . . . . . . . . . Related Publications:. . . . . . . Conventions . . . . . . . . . . . Basic Command Syntax . . . . . Command Editor . . . . . . . . Memory Arrangements. . . . . . Bit-Map Compression Algorithm . Data-to Card Mapping . . . . . . Control Commands . . . . . . . Card Handling Process . . . . . Batch...