Manual De Vcds-908

VCDS Release 908 PDF Manual Printing Instructions:

User’s Manual
Diagnostic Software for VW/Audi/SEAT/Skoda

Release 908
Copyright (c) 2000-2009 by Ross-Tech, LLC. 881 Sumneytown Pike Lansdale, PA 19446 +1-267-638-2300 www.Ross-Tech.com

Disclaimer: All rights reserved, No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by anymeans, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Ross-Tech, LLC. The information contained herein is designed only for use with VCDS diagnostic software. Ross-Tech, LLC. is not responsible for any use of this information as applied to this or other diagnostic equipment. Neither Ross-Tech, LLC. nor its affiliates shall be liable to thepurchaser of this product or third parties for damages, losses, costs, or expenses incurred by purchaser or third parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or failure to comply with Ross-Tech, LLC’s written instructions. By using VCDS, you acknowledge that this Program is provided "as is" and "with allfaults, defects and errors" and that all use of the Program is at your own full risk. It has been extensively tested, but we cannot guarantee it will work correctly with every system in every car. We will make our best effort to fix any bugs and to enhance the program, but we specifically disclaim any liability for damage to your computer or your car, and we do not promise to have any particularenhancements available on any specific date.

Copyright © 2009 by Ross-Tech, LLC

VCDS Table of Contents
Subject Getting Started Main Screen Select Control Module Open Controller Fault Codes Measuring Blocks Data Logging Single Reading Supported Codes Readiness Advanced Identification Advanced Measuring Values Acceleration Measurement Login 7-digit PIN/SKC Dialog Basic Settings Output TestsRecode / Long Coding Adaptation Security Access Auto-Scan SRI Reset Generic OBD2 Applications Transport Mode Controller Channels Map EDC-15-16 Mileage Control Module Finder Optical Bus Diagnostics Options About Problems & Issues FAQ (Frequently Asked Questions) VC-Scope TDI Timing Checker VAG Functions What’s New in Release 908 Section 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 2526 27 28 29 30 31 32 33 34 35 36 37

VCDS - Getting Started - Section 1-A
Thank you for purchasing VCDS, which allows you to turn a Windows PC into a powerful diagnostic tool for VW/Audi/SEAT/Skoda vehicles from 1990 through the latest models.

Read This First!
Before plugging anything in, you must first install VCDS software on your PC.

Step #1
Go to our website and click on Download atthe top of the screen to download and install the latest version of VCDS: www.Ross-Tech.com

Run the installation file that you have downloaded and follow the onscreen instructions and allow VCDS to install in its default directory. ►

The VCDS Pro-Kit comes with a CD containing our software as well. If possible it is always a good idea to download the latest version from our website.◄Step #2
Connect the USB end of your USB Interface or the Serial end of your Serial Interface or the to the correct port on your PC. If your PC is further from the vehicle’s diagnostic port than 6 feet, connect an approved Extension Cable between the PC and the Interface. The appropriate extension is included in the ProKit and additional ones are available from our web store.

Getting Started -Section 1-B

Step #3 (USB Only) ►
If you are using a Serial Interface then you can proceed to step #4. If you are using a USB Interface, a message like this should pop up: ► Click on the Found New Hardware message and the Found New Hardware Wizard should start up. If you are prompted with the choice, pick “No, Not This Time” when asked if you want to connect to the Internet to search for...