Manual estacion total leica ts02

Leica FlexLine TS02/TS06/TS09 User Manual

Version 1.0 English

Introduction

FlexLine, 2

Introduction
Purchase Congratulations on the purchase of a FlexLine instrument. This manual contains important safety directions as well as instructions for setting up and operating the product. Refer to "13 Safety Directions" for further information. Read carefully through the User Manual beforeyou switch on the product. Product identification The model and serial number of your product are indicated on the type plate. Enter the model and serial number in your manual and always refer to this information when you need to contact your agency or Leica Geosystems authorised service workshop. Model: Serial No.: __________________________________________________________________________________________________________________

Symbols

The symbols used in this manual have the following meanings: Type Danger Warning Caution Description Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Indicates a potentially hazardous situation or an unintended use which, if not avoided, could result in death or serious injury. Indicates apotentially hazardous situation or an unintended use which, if not avoided, may result in minor or moderate injury and/or appreciable material, financial and environmental damage. Important paragraphs which must be adhered to in practice as they enable the product to be used in a technically correct and efficient manner.

Trademarks

• Windows is a registered trademark of Microsoft Corporation.• Bluetooth is a registered trademark of Bluetooth SIG, Inc. All other trademarks are the property of their respective owners.

Introduction

FlexLine, 3

Introduction Validity of this manual General Description

FlexLine, 4

This manual applies to TS02, TS06, and TS09 instruments. Where there are differences between the various instruments they are clearly described. The followingsymbols will identify in each section where the instruments differ: • • • for TS02. for TS06. for TS09. Measuring with Prism mode: When measuring distances to a reflector with Electronic Distance Measurement (EDM) mode "Prism", the telescope uses a wide visible red laser beam, which emerges coaxially from the telescope's objective. Measuring with Non-Prism modes: Instruments that are equipped with areflectorless EDM additionally offer the EDM mode "Non-Prism". When meauring distances with this EDM mode, the telescope uses a narrow visible red laser beam, which emerges coaxially from the telescope's objective.

Telescope

•

•

Table of Contents
In this manual Chapter 1 Description of the System 1.1 1.2 1.3 2 System Components Container Contents Instrument Components Page 12 12 14 1619 19 21 22 24 25 27 29 29 35 37 37 39 40

User Interface 2.1 2.2 2.3 2.4 2.5 2.6 Keyboard Screen Status Icons Softkeys Operating Principles Pointsearch

3

Operation 3.1 3.2 3.3 3.4 3.5 3.6 Instrument Setup Working with the Battery Data Storage Main Menu Q-Survey Application Distance Measurements - Guidelines for Correct Results

Table of Contents

FlexLine, 5

Table of Contents 4Setting 4.1 4.2 4.3 5 Tools 5.1 5.2 5.3 5.4 5.5 5.6 6 Adjust Start Up Sequence System Information Licence Keys Instrument Protection with PIN Loading Software General Settings EDM Settings Communication Parameters

FlexLine, 6 42 42 54 60 63 63 64 65 67 68 70 72 72 74 74 76 80 81 84 86 87 Standard Coding 87

Functions 6.1 6.2 Overview Target Offset 6.2.1 Overview 6.2.2 Cylinder OffsetSubapplication Height Transfer Hidden Point Check Tie EDM Tracking

6.3 6.4 6.5 6.6 7 Coding 7.1

7.2 8

Quick Coding

89 91 91 92 94 95 97 97 98 99 103 103 104 105 111 111 113 114 115 118 118 119 120 123 FlexLine, 7

Applications - Getting Started 8.1 8.2 8.3 8.4 8.5 Overview Starting an Application Setting the Job Setting the Station Setting the Orientation 8.5.1 Overview 8.5.2 Manual...