Manual Piping Solid Works

SolidWorks
Piping

SolidWorks Corporation 300 Baker Avenue Concord, Massachusetts 01742 USA

© 1995-2002, SolidWorks Corporation 300 Baker Avenue Concord, Massachusetts 01742 USA All Rights Reserved. U.S. Patents 5,815,154, 6,219,049, 6,219,055 SolidWorks Corporation is a Dassault Systemes S.A. (Nasdaq:DASTY) company. The information and the software discussed in this document are subjectto change without notice and should not be considered commitments by SolidWorks Corporation. No material may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose without the express written permission of SolidWorks Corporation. As a condition to your use of this software product, you agree to accept the limited warranty, disclaimer and other terms andconditions set forth in the SolidWorks Corporation License and Subscription Service Agreement, which accompanies this software. If, after reading the License Agreement, you do not agree with the limited warranty, the disclaimer or any of the other terms and conditions, promptly return the unused software and all accompanying documentation to SolidWorks Corporation and your money will be refunded.The software discussed in this document is furnished under a license and may be used or copied only in accordance with the terms of this license. All warranties given by SolidWorks Corporation as to the software and documentation are set forth in the SolidWorks Corporation License and Subscription Service Agreement, and nothing stated in, or implied by, this document or its contents shall beconsidered or deemed a modification or amendment of such warranties. SolidWorks® and the SolidWorks logo are the registered trademarks of SolidWorks Corporation. SolidWorks 2001Plus is a product name of SolidWorks Corporation. FeatureManager® is a jointly owned registered trademark of SolidWorks Corporation. Feature Palette™ and PhotoWorks™ are trademarks of SolidWorks Corporation. ACIS® is aregistered trademark of Spatial Technology Inc. IGES Access Library is a trademark of IGES Data Analysis, Inc. FeatureWorks® is a registered trademark of Geometric Software Solutions Co. Limited. GLOBEtrotter® and FLEXlm® are registered trademarks of Globetrotter Software, Inc.

Other brand or product names are trademarks or registered trademarks of their respective holders.

COMMERCIAL COMPUTERSOFTWARE - PROPRIETARY U.S. Government Restricted Rights. Use, duplication or disclosure by the Government is subject to restrictions as set forth in FAR 52.227-19 (Commercial Computer Software - Restricted Rights), DFARS 252.227-7202(Commercial Computer Software and Commercial Computer Software Documentation) and in the license agreement, as applicable. Contractor/Manufacturer: SolidWorks Corporation,300 Baker Avenue, Concord, Massachusetts 01742 USA Portions of this software are copyrighted by and are the property of Unigraphics Solutions Inc. Portions of this software © 1990-2002 D-Cubed Limited. Portions of this software © 1998-2002 Geometric Software Solutions Co. Limited. Portions of this software © 1999-2002 Immersive Design, Inc. Portions of this software © 1990-2002 LightWork DesignLimited. Portions of this software © 1996-2002 Microsoft Corporation. All Rights Reserved. Portions of this software © 1995-2002 Spatial Corporation Portions of this software © 1999-2002 Viewpoint Corporation Portions of this software © 1997-2002 Virtue 3D, Inc. All Rights Reserved.

SolidWorks Piping Training Manual

Table of Contents

Piping Basics Introduction. . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Activating SolidWorks Piping . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Specifying Piping Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Required Features of Piping Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Pipes . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....