Manual Reloj Checaor
Páginas: 21 (5082 palabras)
Publicado: 29 de mayo de 2012
®
Electronic Time Recorder Operation Manual
PIX-21 2
SAFETY
Installation, maintenance, etc. of this apparatus should only be performed by a qualified electrician.
PROPRIETARY NOTICE
This document contains proprietary information and such information may not be reproduced in whole or in part without the written permission from Amano Cincinnati, Inc., 140 Harrison Avenue, Roseland,New Jersey, 07068 Amano Cincinnati, Inc. reserves the right to make equipment changes and improvements which may not be reflected in this document. Portions of this document may have been updated to include the latest hardware or firmware version, if applicable. We recommend that this document be read in its entirety before any attempt is made to operate the equipment.
Before You Begin
TheDaylight Saving Time date settings have been preset. DO NOT change the Daylight Saving Time date settings unless you live in Arizona, Hawaii, parts of Indiana, or any other area that does not use Daylight Saving TIme.
Page 1
External View
Removing the Cover & Packing Materials
1. Lift the printer block and remove
the spacer.
2. Insert the key provided and turn clockwise to open thecase. Lift the cover to remove.
Page 2
3. Remove the spacer between the Ribbon Cartridge and the Printer Carriage. 4. Re-install the cover. Your PIX-21 is ready for use!
Front Panel Description
LCD Display Window
Print/Change Button
Print/Enter Button
The RESET Button is located on the bottom of the clock. It is used with the CHANGE or ENTER Button to start the Program mode.When in the Program mode, press the PRINT/CHANGE Button to change data or advance to the next menu selection. When in the Program mode, press the PRINT/ENTER Button to accept a value or enter a selection into memory. When in the Normal mode, the PIX-21 as a default will automatically print when a time card or piece of paper is inserted. This default can be changed in the Program mode to require bothPRINT buttons to be pressed simultaneously in order to print.
Page 3
Mounting the Clock
1. Remove the mounting bracket from the clock by pushing forward on the top tabs “A” and then pushing the tabs down “B” (See below). 2. If you are using the Mobile Mounting Unit gooseneck and special mounting bracket (P/N AJR-208800), mount the gooseneck to the vehicle in the desired location first.Mount the special mounting bracket to the gooseneck using the three #M5 acorn nuts and washers provided. You may discard the original PIX mounting bracket if you wish. 3. If you are not using the Mobile Mounting Unit, securely mount the PIX mounting bracket on the wall using three #10 wood screws or equivalent. 4. Refer to the illustration below to plug the appropriate power cord into the bottomrear of the clock.
If you are using the DC power cord, locate the rubber grommet on the power cord and install the grommet into the notch in the housing. The power cord will exit the clock through the opening on the bottom. Refer to page 16 for more information about using the DC power cord.
Page 4
Quick Program Mode
These instructions must be followed in the order in which they are given.The PIX-21 has two programming modes: Normal and Quick. Either mode may be accessed by simply entering a specific password. To enter the Normal programming mode, use the password “8088” and follow the instructions to program all the items. Refer to page 9 to enter the Normal mode password. For a quick setup of a particular item in the PIX-21, use the alternate password which correlates to theprint style of choice. (See chart on page 5.) The “Quick” mode shortens the print style setup. Refer to page 6 to enter the Quick mode.
1. Understanding the Front Panel
LCD Display Window
Print/Change Button
Print/Enter Button
2. Plug In the Power Cord and Make a Test Print
Insert a piece of paper or time card into the PIX-21. The clock will automatically print a 4-digit YEAR,...
Electronic Time Recorder Operation Manual
PIX-21 2
SAFETY
Installation, maintenance, etc. of this apparatus should only be performed by a qualified electrician.
PROPRIETARY NOTICE
This document contains proprietary information and such information may not be reproduced in whole or in part without the written permission from Amano Cincinnati, Inc., 140 Harrison Avenue, Roseland,New Jersey, 07068 Amano Cincinnati, Inc. reserves the right to make equipment changes and improvements which may not be reflected in this document. Portions of this document may have been updated to include the latest hardware or firmware version, if applicable. We recommend that this document be read in its entirety before any attempt is made to operate the equipment.
Before You Begin
TheDaylight Saving Time date settings have been preset. DO NOT change the Daylight Saving Time date settings unless you live in Arizona, Hawaii, parts of Indiana, or any other area that does not use Daylight Saving TIme.
Page 1
External View
Removing the Cover & Packing Materials
1. Lift the printer block and remove
the spacer.
2. Insert the key provided and turn clockwise to open thecase. Lift the cover to remove.
Page 2
3. Remove the spacer between the Ribbon Cartridge and the Printer Carriage. 4. Re-install the cover. Your PIX-21 is ready for use!
Front Panel Description
LCD Display Window
Print/Change Button
Print/Enter Button
The RESET Button is located on the bottom of the clock. It is used with the CHANGE or ENTER Button to start the Program mode.When in the Program mode, press the PRINT/CHANGE Button to change data or advance to the next menu selection. When in the Program mode, press the PRINT/ENTER Button to accept a value or enter a selection into memory. When in the Normal mode, the PIX-21 as a default will automatically print when a time card or piece of paper is inserted. This default can be changed in the Program mode to require bothPRINT buttons to be pressed simultaneously in order to print.
Page 3
Mounting the Clock
1. Remove the mounting bracket from the clock by pushing forward on the top tabs “A” and then pushing the tabs down “B” (See below). 2. If you are using the Mobile Mounting Unit gooseneck and special mounting bracket (P/N AJR-208800), mount the gooseneck to the vehicle in the desired location first.Mount the special mounting bracket to the gooseneck using the three #M5 acorn nuts and washers provided. You may discard the original PIX mounting bracket if you wish. 3. If you are not using the Mobile Mounting Unit, securely mount the PIX mounting bracket on the wall using three #10 wood screws or equivalent. 4. Refer to the illustration below to plug the appropriate power cord into the bottomrear of the clock.
If you are using the DC power cord, locate the rubber grommet on the power cord and install the grommet into the notch in the housing. The power cord will exit the clock through the opening on the bottom. Refer to page 16 for more information about using the DC power cord.
Page 4
Quick Program Mode
These instructions must be followed in the order in which they are given.The PIX-21 has two programming modes: Normal and Quick. Either mode may be accessed by simply entering a specific password. To enter the Normal programming mode, use the password “8088” and follow the instructions to program all the items. Refer to page 9 to enter the Normal mode password. For a quick setup of a particular item in the PIX-21, use the alternate password which correlates to theprint style of choice. (See chart on page 5.) The “Quick” mode shortens the print style setup. Refer to page 6 to enter the Quick mode.
1. Understanding the Front Panel
LCD Display Window
Print/Change Button
Print/Enter Button
2. Plug In the Power Cord and Make a Test Print
Insert a piece of paper or time card into the PIX-21. The clock will automatically print a 4-digit YEAR,...
Leer documento completo
Regístrate para leer el documento completo.