Manual servicio toshiba e-studio 160

DIGITAL PLAIN PAPER COPIER

DP1600/2000/2500

File No. 31110004 R0111216700-TTEC Ver07_2002-06

Copyright 2000

TOSHIBA TEC CORPORATION

GENERAL PRECAUTIONS REGARDING THE INSTALLATION AND SERVICE FOR DP1600/2000/2500 SERIES
The installation and service should be done by a qualified service technician.

1. Transportation
• When transporting/installing the copier, employ two personsand be sure to use the positions as indicated below. The copier is fairly heavy and weighs approximately 50 kg (110 lb), therefore pay full attention when handling it.

4 portions

2. Installation
• • • • • • Be sure to use a dedicated outlet with AC 115 or 120V/15A (220V, 230V, 240V/10A) or more for its power source. The copier must be grounded for safety. Never ground it to a gas pipe or awater pipe. Select a suitable place for installation. Avoid excessive heat, high humidity, dust, vibration and direct sunlight. Also provide proper ventilation as the copier emits a slight amount of ozone. To insure adequate working space for the copying operation, keep a minimum clearance of 80 cm (32") on the left, 80 cm (32") on the right and 10 cm (4") in the rear. After having installed thecopier, be sure to push the carrying handles into the copier.

3. Service of Machines
• • • • • • Basically, be sure to turn the main switch off and unplug the power cord during service. Be sure not to touch high-temperature sections such as the exposure lamp, the fuser unit, the damp heater and their periphery. Be sure not to touch high-voltage sections such as the chargers and thehigh-voltage transformer. Be sure not to touch rotating/operating sections such as gears, belts, pulleys, fans, etc. When servicing the machines with the main switch turned on, be sure not to touch live sections and rotating/operating sections. Avoid exposure to laser radiation. Use suitable measuring instruments and tools.

December 2000 © TOSHIBA TEC

1600/2000/2500 GENERAL PRECAUTIONS

•

Avoidexposure to laser radiation during servicing. – Avoid direct exposure to beam. – Do not insert tools, parts, etc. that are reflective into the path of the laser beam. – Remove all watches, rings, bracelets, etc. that are reflective.

4. Main Service Parts for Safety
• The breaker, door switch, fuse, thermostat, thermofuse, thermistor, etc. are particularly important for safety. Be sure tohandle/install them properly.

5. Cautionary Labels
• During servicing, be sure to check the rating plate and the cautionary labels such as “Unplug the power cord during service”, “Hot area”, “Laser warning label” etc. to see if there is any dirt on their surface and whether they are properly stuck to the copier.

6. Disposition of Consumable Parts/Packing Materials
• Regarding the recovery anddisposal of the copier, supplies, consumable parts and packingm a terials, it is recommended to follow the relevant local regulations or rules.

7. When parts are disassembled, reassembly is basically the reverse of disassembly unless otherwise noted in this manual or other related documents. Be careful not to reassemble small parts such as screws, washers, pins, E-rings, toothed washers in thewrong places. 8. Basically, the machine should not be operated with any parts removed or disassembled. 9. Precautions Against Static Electricity
• The PC board must be stored in an anti-electrostatic bag and handled carefully using a wristband, because the ICs on it may become damaged due to static electricity. Caution: Before using the wrist band, pull out the power cord plug of the copier andmake sure that there is no uninsulated charged objects in the vicinity. Caution: Dispose of used batteries and RAM-ICs including lithium batteries according to the manufacturer's instructions. Attention: Se débarrasser de batteries et RAM-ICs usés y compris les batteries en lithium selon les instructions du fabricant. Vorsicht: Entsorgung des gebrauchten Batterien und RAM-ICs (inklusive der...