Manual Solar

60 WATT SOLAR 12 VOLT POWER GENERATOR KIT GÉNÉRATRICE SOLAIRE 12VOLTS 60 WATTS INSTRUCCIONES KIT GENERADOR SOLAR 60 W

User’s Manual Notice D’utilisation Manual del Usario

60 WATT SOLAR 12 VOLT POWER GENERATOR KIT
READ this manual BEFORE and DURING the use of this product.

ITEMS INCLUDED: 1. Four 15 Watt Solar Panels 2. Charge Controller 3. 12’ Extension Cable 4. Connector to 12Volt DCplug 5. Connector to 12Volt DC socket 6. 12VDC Socket to Battery Clamps 7. Connector to Battery Clamps 8. Connector to Regulator 9. Inverter 10. 4 in 1 connector 11. PVC Mounting Frame 12. Screws and Nuts for Mounting

1. Pick location of setup - Choose Location with greatest sunlight throughout the day 2. Setup PVC support frame 3. Place panels 4. Connect panels to 4 in1 connector 5. Connectextension to 4 in 1 connector 6. Connect to charge controller 7. Connect charge controller to battery 8. Connect either 12VDC socket to battery to use 12V items or the included inverter to use AC items. 9. Generate Power! INSTALLATION STEPS 1. Pick Location Choose Location with greatest sunlight throughout the day. 2. Setup PVC support Frame. Place all parts together and secure with includedscrews. Be sure that all screws are tight and solid.

3. Place Panels Place panels one by one with wire hanging from top part of frame. Use included screws to secure panels to frame. 4. Connect wires from panels to 4 to 1 connector – refer to image #10 5. Connect extension to 4 in 1 connector. Make sure connections are all tight. See image #3.

6. Connect to charge controller Connect tinned wire toend of the extension cable. See image #8. Refer to charge controller instructions included below – ensure that all polarity is followed correctly. 7. Connect charge controller to battery.
Connect to a battery: Attach the Battery Charge Controller positive (+) wire to the positive (+) battery terminal. Then connect the Battery Charge Controller negative (-) wire to the negative (-) batteryterminal. WARNING: The alligator clips MUST be placed on to the battery in the aforementioned order—wrong connections may cause sparking or explosion. Connect to Solar Panel: Strip the solar panel wires. Connect positive (+) wire from the solar panel to the positive (+) of the charge controller and the negative (-) wire from the solar panel to the negative (-) of the charge controller. Ensure theconnections are secure. Operation: The Green LED indicates a full-charged battery. When the battery reaches 14.2 V, the Solar Charge Controller will cut out voltage thereby ensuring no overcharging. Yellow light indicates a battery that is being charged. When the battery reaches 13 V, the Battery Charge Controller will cut-in and begin charging. NOTES: • It is normal for both lights to flicker on andoff during normal operation. The Battery Charge Controller should be placed within 5’ of the battery in a dry, well-ventilated area. All connections should be parallel to ensure 12 V system (positive to positive and negative to negative).

8. Connect 12VDC socket to battery to use 12V items or the included inverter to use AC items. 9. For AC devices or appliances use the 200 Watt inverter includedin the kit. Connect the O rings to the battery making sure the positive O ring is attached to the positive battery terminal and the negative O ring is attached to the negative battery terminal. Then simply plug the AC device into the inverter. Remember the start up surge power of the device which is approximately double the continuous power must be under the wattage value of the inverter. Pleaserefer to the inverter manual for operating instructions. It is strongly recommended to turn off the inverter when not in use. The inverter's standby current draw or no load draw is 0.2-0.3A. If the inverter is not turned off after use, it is possible to drain the 18Ahr battery within 3 days. USE OF INCLUDED ADAPTORS Connector to12 Volt DC Plug (#4) This connector allows panels to be connected...