Maquinas

VLT ® Series 2000

Table of Contents

Specification Chart Installation Safety Dimensions Cooling Wiring Quick Setup Operation Programming Group 0 -- Operation and Display Group 1 -- Load and Motor Group 2 -- Reference and Limits Group 3 -- Functions and Timers Group 4 -- Inputs and Outputs Group 5 -- Serial Data Interface Group 6 -- Service and Display Appendix Motor Coil and Filter OptionsPI Regulation Parameter Groups Factory Default Settings Customer Settings Chart

Page 2

4 5 7 8 10 11

16 18 22 25 27 31 38

41 42

46 47

1

Installation; Safety
The VLT® Series 2000 Adjustable Frequency Drive (AFD) contains dangerous voltages when connected to line voltage. Only a competent electrician should carry out the electrical installation. WARNING Improper installation ofthe motor or the AFD may cause equipment failure, serious injury or death. Follow this manual and local and national safety codes.

VLT ® Series 2000
It is possible for the VLT to start upon application of AC power. DO NOT attempt any maintenance on the VLT, motor or system machinery without verifying that the AC power has been disconnected. DO NOT touch any electrical parts after the AC linehas been disconnected for at least 14 minutes. This allows for capacitor discharge.

NOTE: The STOP key on the VLT keypad DOES NOT disconnect the AC line.

Caution:
The motor may start without warning during operation and programming of the parameters. Activate the STOP key on the VLT keypad when changing data. It is the responsibility of the user or the person installing the AFD to provideproper grounding and branch circuit protection for incoming power and motor overload protection according to the National Electrical Code (NEC) and local codes.

Danfoss VLT® and CE Marking
Danfoss CE marks our VLT® Adjustable Frequency Drives (AFD) according to the Electro Magnetic Compatibility (EMC) Directive 89/336/EEC and LowVoltage Directive 73/23/EEC. When the installation specificationis followed and shielded motor cables are used per instruction manuals provided with the drive, we guarantee the AFD complies with the EMC Directive 89/336/EEC. Upon request we will issue a declaration of conformity to the EMC and low-voltage directives. A manufacturer's declaration for the Machinery Directive 89/392/EEC is also available.

4

VLT ® Series 2000
VLT 2010-2030 Single-phase,220-240 V Three-phase, 208-240 V

Installation; Dimensions

4.3 (110) 3.5 (90) 7.1 (180)

0.21 (5.5) 0.29 (7.5) 0.43 (11)

NOTE: Minimum space above and below the unit is 4 inches. Minimum space to the sides of the unit is 0 inches.

9.3 (235) 10.2 (260)

0.21 (5.5) 0.17 (4.5)

VLT 2010-2030 with module Single-phase, 220-240 V Three-phase, 208-240 V

4.3 (110) 3.5 (90) 7.1 (180)0.21 (5.5) 0.29 (7.5) 0.43 (11)

NOTE: Minimum space above and below the unit is 4 inches. Minimum space to the sides of the unit is 0 inches.

14.3 (338) 14.3 (363)

0.21 (5.5) 0.17 (4.5)

5

Installation; Dimensions
VLT 2020-2050 Three-phase, 380-415/460 V VLT 2040-2050 Three-phase, 208-240 V
7.1 (180)

VLT ® Series 2000

4.3 (110) 3.5 (90)

0.21 (5.5) 0.29 (7.5) 0.43 (11)NOTE: Minimum space above and below the unit is 4 inches. Minimum space to the sides of the unit is 0 inches.

13.2 (335) 14.2 (360)

0.21 (5.5) 0.17 (4.5)

VLT 2020-2050 with module Three-phase, 380-415/460 V

4.3 (110) 3.5 (90) 7.1 (180)

0.21 (5.5) 0.29 (7.5) 0.43 (11)

NOTE: Minimum space above and below the unit is 4 inches. Minimum space to the sides of the unit is 0 inches.17.2 (437) 18.2 (462)

0.21 (5.5) 0.17 (4.5)

6

VLT ® Series 2000
Mechanical Installation The VLT Series 2000 is cooled by natural or forced air convection. Therefore air must be able to pass freely under and over the unit The VLT adjustable frequency drive must be mounted on a flat vertical surface. To enable the VLT to get rid of the cooling air, you must allow free air space both above...