Mazda32316Ib6Medidasmotor.Pdf

Adjustment Data MAZDA - 323 - 1.6i - B6
Engine (general) Item Engine code Capacity Idle speed Valve clearance Hydraulic Compression pressure Normal Minimum Oil pressure Fuel system (make & type) Adjustment screws (A = idle speed B = CO) 13.5 9.5 1.95 - 2.94/1000 EGI A (bar) (bar) (bar / rpm) Values B6 1598 850 ± 50 (cc) (rpm) Units

Firing order Timing stroboscopic (before TDC) Vacuum advanceStart End Centrifugal advance Start End Ignition-coil resistance, primary Ignition-coil resistance, secondary Spark plugs (make & type) Spark-plug gap Fuel-pump pressure CO exhaust gas

1-3-4-2 2 ± 1/850 0 ± 3/75 26 - 30/450 0 ± 2/1200 17 ± 2/3500 1.04 - 1.27 6000 - 30000 NGK/BPR5ES11 Bosch FR7DCX 1.0 - 1.1 2.7 - 3.2 < 0.5 (mm) (bar) (%) (° / rpm) (° / mmHg) (° / mmHg) (° / rpm) (° / rpm) (ohms)(ohms)

CO2 HC O2 Lambda Lambda change (Delta Lambda) Oil temperature during test Fast-idle speed CO at fast-idle speed Cooling system Item Cap pressure Thermostat opens at Fan on at Electrical Item Battery Alternator Brakes Item Disc thickness, front, min. Drum diameter, rear, max. Steering and wheel alignment Item Toe-in, front Camber, front Castor, front K.P.I., front Toe-in, rear Camber,rear Wheels and tyres Item Tyre size Optional Front tyre pressure Rear tyre pressure Capacities Item Engine sump, incl. filter Manual transmission Values Values 50 65

> 14 100 0.3 ± 0.2 0.98-1.03 0.03 60 2500-2800 < 0.3

(%) (ppm) (%)

(°C) (rpm) (%)

Values 0.75 - 1.05 82 97

Units (bar) (°C) (°C)

Units (Ah) (A)

Values 16.0 201

Units (mm) (mm)

Values 12' ± 18' -5' ± 45' 2°05' ± 45' 12° 25' 12' ± 18' -20' ± 45'

Units (°) (°) (°) (°) (°) (°)

Units

155/80R13 175/70R13 2.0 1.8 (bar) (bar)

Values 3.4

Units (l)

Gearbox refill Cooling system Torque settings Item Cylinder head Values

2.68 5.0

(l) (l)

Units

Stage 1 Stage 2 Stage 3 Front hub Wheel nuts Spark plugs

20-30 40-60 76-81 157 - 235 90 - 120 15 - 23
© Copyright, Wessels + Mьller AG(Nm) (Nm) (Nm) (Nm) (Nm) (Nm)

Environmental Data MAZDA - 323 - 1.6i - B6
Item Engine code Idle speed Fuel system (make & type) Adjustment screws (A = idle speed B = CO) Values B6 850 ± 50 EGI A (rpm) Units

Timing stroboscopic (before TDC) Vacuum advance Start End Centrifugal advance Start End Fuel-pump pressure CO exhaust gas CO2 HC O2 Lambda Lambda change (Delta Lambda) Oil temperatureduring test Fast-idle speed CO at fast-idle speed
© Copyright, Wessels + Mьller AG

2 ± 1/850 0 ± 3/75 26 - 30/450 0 ± 2/1200 17 ± 2/3500 2.7 - 3.2 < 0.5 > 14 100 0.3 ± 0.2 0.98-1.03 0.03 60 2500-2800 < 0.3

(° / rpm) (° / mmHg) (° / mmHg) (° / rpm) (° / rpm) (bar) (%) (%) (ppm) (%)

(°C) (rpm) (%)

Error codes

Diagnostic plug Diagnostic plug: 1 = Datalink LED tester (FEN) 3 =activation error codes (TEN) 4 = positive battery terminal (+B) 5 = ground Read-out -Connect LED tester to positive battery terminal and diagnostic-plug terminal 1. -Connect diagnostic-plug terminal 3 to ground. -Turn ignition on. -Error codes will appear on LED tester. Reset -Turn ignition off. -Disconnect negative terminal of the battery. -Depress brake pedal for at least 5 seconds. -Connect negativeterminal of the battery. -Verify that no error codes are displayed. Signal -Digit 1 (tens position): Light pulse 1.2 seconds long, 0.4 seconds pause in-between. -Pause 1.6 seconds light-off. -Digit 2 (units position): Light pulse 0.4 seconds long, 0.4 seconds pause in-between. -Pause 4.0 seconds light-off. Error codes 02 Hall sensor, no signal (SGT). 03 Hall sensor, no signal (SGC, DOHC engines).08 Airflow meter, open or short circuit. 09 Coolant temperature sensor, open or short circuit. 10 Air temperature sensor, open or short circuit. 12 Idle and throttle wide open switch open or short circuit. 14 Absolute pressure sensor (inside ECU), open or short circuit. 15 Oxygen sensor, lean signal for longer than 86 seconds, engine speed is higher than 1500 rpm, warm engine. 17 Oxygen sensor...