MetroEthernet RedIris
Jornadas Técnicas RedIRIS 2005
Gustavo Sánchez Gómez
Agenda
Ethernet: historia y estándares
Servicios
Metro Ethernet Forum: MEF
Misión y objetivos and objectives
Definición y tipos de servicio
Actividad de estandarización
Metro Ethernet y tecnologías de transporte
EoW
EoS
EoMPLS, etc
Conclusiones
Ethernet
Historia y estándares
Qué es ethernet?
Conjunto de estándares para la capa física y la capa MAC,
para la transmisión de datos
Inventado por Robert M. Metcalfe en 1973 cuando
trabajaba en Xerox.
Consorcio DIX y despues se estandarizó por el IEEE
http://www.ethermanage.com/
Se basa en los estándares 802.3 de IEEE
suplemento
año
descripción
802.3a
1985
Original 802.3: 10BASE-5 10BASE-2 10BROAD-36
802.3c
1986Especificaciones de repetidores
802.3d
1987
FOIRL (enlace de fibra)
802.3i
1990
10Base-T Ethernet sobre par trenzado de cobre
802.3j
1993
10Base-F Ethernet sobre fibra
802.3u
1995
100Mbps Ethernet
802.3x e 802.3y
1997
operación full duplex
802.3z
1998
1000Base-X (Gigabit Ethernet)
802.3ab
1999
1000Base-T (GE sobre par trenzado)
802.3ac
1998
Extensiones de trama (hasta 1522 bytes) paraVLANs
802.3ad
2000
link aggregation
802.3ae
2002
10 GE
802.3af
2003
PoE (Power over Ethernet). Hasta 15W
802.3ah
2004
Ethernet in First Mile
802.3an
10 Gbase-T (en draft)
Bridging en 802.1D
802.1w
Cambios y mejoras en el spanning tree
802.1s
Múltiples spanning trees
Estándares de ethernet sobre optico
ITU-T G.7041 Generic Framing Procedure (GFP)
ITU-TX.86 Link Access Protocol (LAPS)
ITU-T H.707 Virtual Concatenation (VCAT)
ITU-T G.7042 Link Capacity Adjustment Scheme (LCAS)
Otros:
IEEE 802.1X Port Based Network Access Control
IEEE 802.1D Ethernet switching
IEEE 802.1Q Virtual LAN (VLAN)
IEEE 802.1P Priorización de tráfico a nivel 2
IETF: MPLS Multi-Protocol Label Switching
IEEE 802.17 Resilient Packet Ring (RPR)
Ver:
http://grouper.ieee.org/groups/802/3/
http://grouper.ieee.org/groups/802/1/
Trama ethernet
Los datos trasmitidos se encapsulan en un
contenedor, que se llama trama
Este formato de trama DEFINE Ethernet
Históricamente, existen dos tipos de tramas:
»802.3 Framing usa en campo de longitud de trama
(Length) despues del campo de Source Address
»Ethernet II (DIX) Framing usa(ba) el campo de tipo de
trama (type)despues del campo Source Address
Ambos tipos de tramas están definidos y soportados
dentro de IEEE 802.3
Trama ethernet
El tamaño de trama varía desde 64 a 1518 Bytes,
escepto cuando se usa el identificadir (tag) de VLAN
802.1Q/P
3
1
User Priority CFI
12
Bits of VLAN ID (VIDI) to identify possible VLANs
User Priority- Defines user priority, giving eight (2^3) priority levels.IEEE 802.1P defines the
operation for these 3 user priority bits.
CFI- Canonical Format Indicator is always set to zero for Ethernet switches. CFI is used for
compatibility reason between Ethernet type network and Token Ring type network. If a frame
received at an Ethernet port has a CFI set to 1, then that frame should not be forwarded as it is to an
untagged port.
VID- VLAN ID is theidentification of the VLAN, which is basically used by the standard 802.1Q. It
has 12 bits and allow the identification of 4096 (2^12) VLANs. Of the 4096 possible VIDs, a VID of 0
is used to identify priority frames and value 4095 (FFF) is reserved, so the maximum possible VLAN
configurations are 4,094.
Length/Type- 2 bytes. This field indicates either the number of MAC-client data bytes that arecontained in the data field of the frame, or the frame type ID if the frame is assembled using an
optional format.
Data- Is a sequence of nbytes (48=< n =<1500) of any value. The total frame minimum is 64bytes.
Frame check sequence (FCS)- 4 bytes. This sequence contains a 32-bit cyclic redundancy check
(CRC) value, which is created by the sending MAC and is recalculated by the receiving MAC to...
Regístrate para leer el documento completo.