Norma mil-dtl-17901c (2) bujes de caucho bac

Downloaded from http://www.everyspec.com on 2009-04-24T17:28:15.

INCH-POUND MIL-DTL-17901C(SH) 10 May 2005 SUPERSEDING MIL-B-17901B(SH) AMENDMENT 3 12 December 1990 DETAIL SPECIFICATION BEARING COMPONENTS, BONDED SYNTHETIC RUBBER, WATER LUBRICATED This specification is approved for use by the Naval Sea Systems Command, Department of the Navy, and is available for use by all Departments andAgencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers stave shaped and cylindrical shaped bearings that have synthetic rubber facings. 1.2 Classification. Bearings are of the following classes, as specified (see 6.2): 1.2.1 Classes. (Note: Class I replaced with class III). Class II - Cylindrical bearing, with cylindrical shaped metal backing and internally molded rubberstave forms. Class III - Stave bearing, nonmetallic backed. Class IV - Cylindrical bearings, with cylindrical shaped nonmetallic backing and internally molded rubber stave forms. Class V - Partial-arc bearing consisting of nonmetallic half cylinders with internally bonded rubber. 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3, 4, or 5 of thisspecification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents cited in sections 3, 4, or 5 of this specification, whether or not they arelisted. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. FEDERAL SPECIFICATIONS QQ-B-639 Brass, Naval: Flat Products (Plate, Bar, Sheet, and Strip)Comments, suggestions, or questions on this document should be addressed to: Commander, Naval Sea Systems Command, ATTN: SEA 05Q, 1333 Isaac Hull Avenue, SE, Stop 5160, Washington Navy Yard DC 20376-5160 or emailed to commandstandards@navsea.navy.mil, with the subject line “Document Comment”. Since contact information can change, you may want to verify the currency of this address information usingthe ASSIST Online database at http://assist.daps.dla.mil AMSC N/A FSC 3130

Downloaded from http://www.everyspec.com on 2009-04-24T17:28:15.

MIL-DTL-17901C(SH)

FEDERAL STANDARDS FED-STD-791 Lubricants, Liquid Fuels, and Related Products; Methods of Testing

DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-P-18324 Plastic Material, Laminated Phenolic, For Bearings (Water or Grease Lubrication)(Copies of these documents are available online at http://assist.daps.dla.mil/quicksearch/ or http://assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2.2 Other Government documents, drawings, and publications. The following other Government documents, drawings, and publications form a part of this document tothe extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation contract. NAVSEA DRAWING NAVSHIPS 803-1385664 Bearings Stern Tube and Strut

(Copies of this document are available from Naval Inventory Control Point, 700 Robbins Avenue, Attn: Code 0862 (Cash Sales), Philadelphia, PA 19111, or www.nll.navsup.navy.mil.) 2.3 Non-Governmentpublications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. AMERICAN NATIONAL STANDARDS INSTITUTE (ANSI) B74.12 Specifications for the Size of Abrasive Grain – Grinding Wheels, Polishing and General Industrial Uses (DoD adopted)

(Copies of this...