Potencia
GENERAL PURPOSE J-FET QUAD OPERATIONAL AMPLIFIERS
s WIDE COMMON-MODE (UP TO VCC+) AND
DIFFERENTIAL VOLTAGE RANGE
s LOW INPUT BIAS AND OFFSET CURRENT s OUTPUT SHORT-CIRCUIT PROTECTION s HIGH INPUT IMPEDANCE J–FET INPUT
STAGE
N DIP14 (Plastic Package)
s INTERNAL FREQUENCY COMPENSATION s LATCH UP FREE OPERATION s HIGH SLEW RATE : 16V/µs (typ)
D SO14 (PlasticMicropackage)
p TSSOP14 (Thin Shrink Small Outline Package)
ORDER CODE DESCRIPTION
Part Number Temperature Range Package N • • • D • • • P • • •
The TL084, TL084A and TL084B are high speed J–FET input quad operational amplifiers incorporating well matched, high voltage J–FET and bipolar transistors in a monolithic integrated circuit. The devices feature high slew rates, low input bias andoffset currents, and low offset voltage temperature coefficient. PIN CONNECTIONS (top view)
TL084M/AM/BM -55°C, +125°C TL084I/AI/BI -40°C, +105°C TL084C/AC/BC 0°C, +70°C Example : TL084CN, TL084CD
N = Dual in Line Package (DIP) D = Small Outline Package (SO) - also available in Tape & Reel (DT) P = Thin Shrink Small Outline Package (TSSOP) - only available in Tape & Reel (PT)
Output 1 1Inverting Input 1 2 Non-inverting Input 1 3 VCC + 4 Non-inverting Input 2 5 Inverting Input 2 6 Output 2 7 + + + +
14 Output 4 13 Inverting Input 4 12 Non-inverting Input 4 11 VCC 10 Non-inverting Input 3 9 8 Inverting Input 3 Output 3
March 2001
1/12
TL084 - TL084A - TL084B
SCHEMATIC DIAGRAM (each amplifier)
VCC
Non-inverting input Inverting input
1 0 0Ω
2 0 0Ω
Output
1 0 0Ω30k
8.2k
1.3k VCC
35k
1.3k
35k
1 0 0Ω
ABSOLUTE MAXIMUM RATINGS
Symbol VCC Vi Vid Ptot Toper Tstg
1. 2. 3. 4.
Parameter Supply voltage - note 1) Input Voltage - note Power Dissipation Output Short-circuit Duration - note 4) Operating Free-air Temperature Range Storage Temperature Range
2) 3)
TL084M, AM, BM
TL084I, AI, BI
TL084C, AC, BC
Unit V V V mW
±18±15 ±30 680 Infinite -55 to +125 -40 to +105 -65 to +150 0 to +70
Differential Input Voltage - note
°C °C
All voltage values, except differential voltage, are with respect to the zero reference level (ground) of the supply voltages where the zero reference level is the midpoint between VCC + and VCC -. The magnitude of the input voltage must never exceed the magnitude of the supply voltageor 15 volts, whichever is less. Differential voltages are the non-inverting input terminal with respect to the inverting input terminal. The output may be shorted to ground or to either supply. Temperature and/or supply voltages must be limited to ensure that the dissipation rating is not exceeded
2/12
TL084 - TL084A - TL084B
ELECTRICAL CHARACTERISTICS VCC = ±15V, Tamb = +25°C (unlessotherwise specified)
Symbol Parameter Input Offset Voltage (Rs = 50Ω) Tamb = +25°C Vio Tmin ≤ Tamb ≤ Tmax TL084I,M,AC,AI,AM, BC,BI,BM Min. TL084 TL084A TL084B TL084 TL084A TL084B Typ. 3 3 1 Max. 10 6 3 13 7 5 Min. TL084C Unit Typ. 3 Max. mV 10
13
DVio Iio
Input Offset Voltage Drift Input Offset Current - note Tamb = +25°C Tmin ≤ Tamb ≤ Tmax Input Bias Current -note 1 Tamb = +25°C Tmin ≤ Tamb≤ Tmax Large Signal Voltage Gain (RL = 2kΩ, Vo = ±10V) Tamb = +25°C Tmin ≤ Tamb ≤ Tmax Supply Voltage Rejection Ratio (RS = 50Ω) Tamb = +25°C Tmin ≤ Tamb ≤ Tmax Supply Current, no load, per amplifier Tamb = +25°C Tmin ≤ Tamb ≤ Tmax Input Common Mode Voltage Range Common Mode Rejection Ratio (RS = 50Ω) Tamb = +25°C Tmin ≤ Tamb ≤ Tmax Output Short-circuit Current Tamb = +25°C Tmin ≤ Tamb ≤ Tmax OutputVoltage Swing Tamb = +25°C RL = 2kΩ RL = 10kΩ RL = 2kΩ RL = 10kΩ ±11 50 25 80 80
1)
10 5 100 4 200 20 25 15 70 70 2.5 2.5 ±11
10 5 100 4 400 20
µV/°C pA nA pA nA V/mV
Iib
20
20
Avd
200
200 dB
SVR
86
86 mA
ICC Vicm CMR
1.4 +15 -12 86
1.4 +15 -12 86
2.5 2.5 V dB
80 80 10 10 10 12 10 12 8
70 70 60 60 10 10 10 12 10 12 8
mA 40 40 60 60 V...
Regístrate para leer el documento completo.