Practica5

Standard Specification for

Nickel-Chromium-Iron Alloys (UNS N06600, N06601, N06603, N06690, N06025, and N06045)* and Nickel-Chromium-CobaltMolybdenum Alloy (UNS N06617) Seamless Pipe and Tube1
This standard is issued under the fixed designation B 167; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision.A number in parentheses indicates the year of last reapproval. A superscript epsilon (e) indicates an editorial change since the last revision or reapproval. This standard has been approved for use by agencies of the Department of Defense.

1. Scope 1.1 This specification2 covers nickel-chromium-iron alloys (UNS N06600, N06601, N06603, N06690, N06025, and N06045)* andnickel-chromium-cobalt-molybdenum alloy (UNS N06617) in cold-worked annealed, hot-worked annealed, and hot-finished seamless pipe and tube intended for general corrosion resistant and heat resistant applications. 1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 The following safety hazards caveat pertains only to the test methodsportion, Section 12, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 2. Referenced Documents 2.1 ASTM Standards: B 880 Specification for GeneralRequirements for Chemical Check Analysis Limits for Nickel, Nickel Alloys and Cobalt Alloys3 E 8 Test Methods for Tension Testing of Metallic Materials4 E 29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications5 E 38 Methods for Chemical Analysis of Nickel-Chromium and Nickel-Chromium-Iron Alloys6 E 1473 Test Methods for Chemical Analysis of Nickel,
1 Thisspecification is under the jurisdiction of ASTM Committee B02 on Nonferrous Metals and Alloys and is the direct responsibility of Subcommittee B02.07 on Refined Nickel and Cobalt and Their Alloys. Current edition approved Oct. 10, 2000. Published December 2000. Originally published as B 167 – 41 T. Last previous edition B 167 – 98 * New designation established in accordance with Practice E 527 and SAE J1086, Practice for Numbering Metals and Alloys (UNS). 2 For ASME Boiler and Pressure Vessel Code applications see related Specification SB-167 in Section II of that Code. 3 Annual Book of ASTM Standards, Vol 02.04. 4 Annual Book of ASTM Standards, Vol 03.01. 5 Annual Book of ASTM Standards, Vol 14.02. 6 Discontinued—See 1989 Annual Book of ASTM Standards, Vol 03.05.

Cobalt, and High-TemperatureAlloys7 2.2 Federal Standards:8 Fed. Std. No. 102 Preservation, Packaging and Packing Levels Fed. Std. No. 123 Marking for Shipment (Civil Agencies) Fed. Std. No. 182 Continuous Identification Marking of Nickel and Nickel-Base Alloys 2.3 Military Standard:7 MIL-STD-129 Marking for Shipment and Storage 3. Terminology 3.1 Definitions of Terms Specific to This Standard: 3.1.1 average diameter—the averageof the maximum and minimum outside diameters, as determined at any one cross section of the pipe or tube. 3.1.2 pipe—tube conforming to the particular dimensions commercially known as pipe sizes. See Table X2.1. 3.1.3 seamless pipe or tube—a pipe or tube produced with a continuous periphery in all stages of the operations. 3.1.4 tube—a hollow product of round or any other cross section having acontinuous periphery. 4. Ordering Information 4.1 It is the responsibility of the purchaser to specify all requirements that are necessary for the safe and satisfactory performance of material ordered under this specification. Examples of such requirements include, but are not limited to, the following: 4.1.1 Alloy Name or UNS Number—see Table 1, 4.1.2 ASTM Designation, including year of issue,...