Propiedades mecanicas (silla)

Error Codes
Code Description 20 Pulser Fail 24 Conversion Factor Changed/ Not Programmed 25 Two-Wire/Standalone Mode Changed 26 Meter Not Calibrated 27 Side 1 Two-Wire ID Changed 28 Side 2 Two-Wire ID Changed 29 Pump Time-Out Error 30 VaporVac® Fail Both Sides or Vapor Sense 5 31 Totals Data Error 32 Pulser Count Error 33 VaporVac Fail One Side or Push-To-Stop Button Activated 35 ConfigurationData Error 36 Unit Type Configuration Code Changed 37 PIN Code 1 Changed 38 PIN Code 2 Changed 39 Cash/Credit Option Changed 40 Master Reset Jumper in Place 41 Side Exists Option Changed 44 Pump Handle Up at Power Up 45 Preset Overrun (minor) 46 Preset Overrun (major)
* Default

Blend Error Codes
Code 4307 4308 4311 4312 4313 4314 4315 4316 4329 Description Blends Not Programmed No Blend TableLow Product Low Flow Hi Product Low Flow Low Product No Flow Hi Product No Flow Hi Product Contaminated by Lo Lo Product Contaminated by Hi Leaky Valve
®

MDE-4039B Encore 300 Programming Quick Reference Card February 2004

Software Versions
For detail on software versions, see MDE-3804 Encore and Eclipse® Service Manual. Power-up and Command Code 8 display the current software version.Single-Hose MPD®
Code Description 4350 Valve Control Option Not Programmed (see CC17) 4351 Valve Leaks - Grade 1 4352 Valve Leaks - Grade 2 4353 Valve Leaks - Grade 3 4355 Valve Leaks - Grade 1 & 2 4356 Valve Leaks - Grade 1 & 3 4358 Valve Leaks - Grade 2 & 3

PIN Code Entry
Level 1- Press F1, enter 4-digit ID (default 2222) then press ENTER. Level 2- From Level 1, enter any Level 2 CommandCode (10-12), enter 4-digit ID (default 1503) then press ENTER. Level 3- From Level 2, enter any Level 3 Command Code (13-17), enter 4-digit ID (default 1309) then press ENTER. Press F1 to exit any command code. Press F2 to return to normal operation.

From Level 2:
Command Code 10: System Configuration Press ENTER after making selections. • Enter 10. • Enter Function #. • Enter Configuration #.Function Code 1 (For non-blenders only): Unit Type Self configures default value. 1 = 1 product 2 = 2 product 3 = 3 product Function Code 2: Money Decimal Point 1 = xxxxx 2 = xxxx.x 3 = xxx.xx * 4 = xxx.xxx Function Code 3: Calculation PPU Decimal Point (Required in U.S. per Weights & Measures) 1 = xxxx 2 = xxx.x 3 = xx.xx 4 = x.xxx * Function Code 4: Displayed PPU Decimal Point Self configuresdefault value. 1 = xxxx 2 = xxx.x 3 = xx.xx 4 = x.xxx Function Code 5: STP Prestart 0 = Off * 1 = On

Eclipse®, Encore®, CRIND®, and VaporVac® are registered trademarks of Gilbarco Inc. Call Gilbarco Technical Support at: 1-800-743-7501 ©2004 Gilbarco Inc. • 7300 W. Friendly Ave., P.O. Box 22087 Greensboro, NC 27420 • Phone # 336-547-5000 • http://www.gilbarco.com

Function Code 6: Beeper Option0 = Off 1 = On * Function Code 8: Two-Wire Display Blank Option: 0 = Off * 1 = On Function Code 9: 5 or 6 Digit Cash Display 0 = 5 Digit Money * 1 = 6 Digit Money Function Code 10: Decimal/Comma Mode 0 = Comma Off* 1 = Comma On Function Code 11: Preselect Time-Out 0 = None 1 = 5 seconds 2 = 15 seconds * 3 = 30 seconds 4 = 45 seconds 5 = 60 seconds 6 = 75 seconds 7 = 90 seconds 8 = 120 secondsFunction Code 12: Pump Time-Out 0 = None * 1 = 5 seconds 2 = 15 seconds 3 = 30 seconds 4 = 45 seconds 5 = 60 seconds 6 = 75 seconds 7 = 90 seconds 8 = 120 seconds Function Code 13 (Ultra-Hi only) Slowdown 0 = .070 gallons (.264 liters) 1 = .120 gallons (.454 liters) * 2 = .170 gallons (.643 liters) 3 = .220 gallons (.833 liters) 4 = .270 gallons (1.02 liters) 5 = .320 gallons (1.21 liters) 6 = .370gallons (1.40 liters) 7 = .420 gallons (1.59 liters) 8 = .470 gallons (1.78 liters) 9 = .520 gallons (1.97 liters) Function Code 14: G6 PUsh to Start 0 = Off* 1 = On Function Code 15: Zero PPU Pricing Option Enable 0 = Disabled *

1 = Enabled Function Code 16: Beeper Time-out 0 = Off * 1 = 5 seconds 2 = 15 seconds 3 = 30 seconds 4 = 45 seconds 5 = 60 seconds 6 = 75 seconds 7 = 90 seconds 8 =...