Prueba

LED DISPLAY VIDEO SCREEN Installation and Calibration Manual

DMX Technologies www.dmxtec.com

Product Model: PH16mm Full color Size: 15.79 square meters Date: 2008-05-25

Table of Contents
Preface 1. Safety precaution 2. Installation screen 2.1 LED Module dimension 2.2 Cabinet structure 2.3 Data cabling diagram 2.4 Power cabling diagram 2.5 Installations selection 2.6 Installing cabinetsto frame work 3. Hardware/software installation and setup 3.1 Graphic Card and Data Sending Card Installation 3.2 Hardware Connection 3.3 Computer configuration 3.4 Software setup 3.5 Calibration 3.6 Software Instruction Manual 4. Spare Parts replacing and maintenance 4.1Spare Parts replacing 4.1.1 LED module replacing 4.1.2 Drive board replacing 4.1.3 Switching power supply replacing 4.2Attention and maintenance 4.3 FAQ 5. Problem shooting

Preface
Thank you for purchasing LED display from DMXTEC. We are submitting the instructions in order to help you to make it easy when installing or use. Please read this manual in detailed and carefully before installation. This document is subject to changes without notice and all right reserved.

1. Safety precaution

● ● ● ●

●

●●

Be aware of the suspended loads； Wear a hard hat to reduce the risk of personal injury； Mind you fingers while working with heavy load； The screen must be installed by experienced professional and keep the screen power off before switch on the computer； The control computer must be used by the screen only, and make sure to keep the computer far away from the virus’ attack； Connect the screenwith the computer reliably, any flexible connection maybe lead to the screen display abnormally, so please don’t touch, draw and push down the cable； The safety of installation place, frame work, installation, collection, use, separation and transportation must be approved by authority；

2. Installation Screen
2.1 LED module dimension

2.2 Cabinet structure

51 41 31 21Rec 11 1

52 42 3222 12 2

53 43 33 23 13 3

54 44 34 24 14 4

55 45 35 25 15 5

56 46 36 26 16 6 Back view

57 47 37 27 17 7

58 48 38 28 18 8

59 49 39 29 19 9

60 50 40 30 20 10

2.3 Data cabling diagram (See the PDF file) 2.4 Power cabling diagram (See the PDF file)

3. Hardware/Software installation and setup
3.1 Visual Card and Data Collecting Card installation
Please operate asillustrated in below figures 3.1.1 Open the computer cabinet, and find out the slot of PCI and PCI-E in main board 3.1.2 Insert the data collecting card into the PCI slot 3.1.3 Insert the visual card into the PCI-E slot

3.2 Connection between computer and screen
Operate as below step by step: 1、Connect computer to data collecting card with a RS232 Serial cable (White, provided) , the end of theDB9-pin female interface to the com port and the RJ45 plug to the data collecting card. 2、Connect the visual card to data collecting card with provided DVI cable (Black). 3、Connect the data collecting card to the 1st receiving card with provided network cable (Grey). 4、Check the whole connection, if there is right then Configuration can be start now.

3.3 Computer configuration
Right click on thespace of your desktop, appearing Figure3-1.

Select “property”, appearing Figure 3-2, then select “option” and then “advance”, appearing Figure 3-3. Then click on “display”, appearing Figure 3-4. Click the red switch in it on FPD item, the switch will turn green, then press “ok”.

Figure 3-3

Figure 3-4

3.4 Software Installation and uninstall 3.4.1 LED Studio software Installation
“LEDStudio” can be easily installed, as shown below: Put the “LED Studio” installation CD into the CD-ROM, The Installation Menu will automatically pop up. (if not, then select this CD-ROM, double click it with your

mouse)Then select “Install LED Studio” to start the Installation Guide, as Shown in Figure 3-5. After that, simply follow the instruction on the screen. Note: This software is...