Reveladora Kodak

Part No. 4E8773
30August01

Kodak Medical X-ray Processor 101/102

Service Manual

Table of Contents
Installation Data ........................................................................................ 3
Trouble Shooting....................................................................................... 6
Spare PartsList....................................................................................... 12
Wiring Charts .......................................................................................... 18
The information contained herein is based on the experience and knowledge relating to the subject matter gained by Eastman Kodak Company prior to publication.
No patent license is granted by this information.
Eastman Kodak Company reserves the right tochange this information without notice, and makes no warranty, express or implied, with respect to this information.
Kodak shall not be liable for any loss or damage, including consequential or special
damages, resulting from any use of this information, even if loss or damage is
caused by Kodak’s negligence or other fault.

Copyright
© 2001 by Kodak. All rights reserved. Any reproduction,out of the limitation by the copyright law, needs written
authorization by Kodak.

To Order Parts or for Technical Support
Type

Phone
Direct Mail

Number
+49 7062 9255 22
PROTEC
Medizintechnik GmbH & Co. KG
Lichtenberger Strasse 35
71720 Oberstenfeld
Germany

Fax

+49 7062 22685

E-Mail

service@protec-med.com

2

Hours
Normal Business Hours:
Central European Time(Berlin, Paris, Rome)
Monday - Thursday: 8 am to 5 pm
Friday: 8 to 12 am (noon)

Installation Data
59 cm (23.2")

Optional working table or closed base
cabinet (accessory)

70 cm (27.6“)
70 cm (27.6")

42 cm (16.5")

77 cm (30.3")

59 cm (23.2“)
59 cm (23.2")

75 cm (29.5“)
75 cm (29.5")
1.

Wall socket
101: 110V, 20A, 102: 220240 V, 16 A (depending on
machine model). Powerlead
should be equipped with
Earth-Leakage Switch, 25 A /
30 mA nominal error-current.
In addition, a wall disconnect
switch can be installed.

Drainage plastic pipe (PVC)
∅ 50 mm (2“) incl. syphon.

Drainage resp. collecting containers for used fixer.

6.

Storing space for replenishment tanks: Below machine or
externally.

7.

Ventilation of darkroom is necessary.

8.Sink with freshwater and flexible hose. Inner dimensions
minimum (LxWxH)
60x40x30 cm (24x16x12“).

8

Sink

60x40cm (24x16’‘)

45
20cm (8’‘)

5.

2

130cm (51’‘)

Drainage resp. collecting containers for used developer.

1

85cm (34’‘)

4.

50cm (20’‘)

Fresh water connection 19
mm (3/4”) with stop cock, permissible pressure 1-6 bar,
water temperature 5-25 °C.

3.7

30cm
(12’‘)

2.

Darkroom

3

6

Measures and positions are recommendations

3

Note: The processor needs ot be ordered as through the wall ready
to be able to install it through the wall.
Through the wall mounting “film output”
Film output to the light room for Kodak processor
553 (21,7”)

705 (27,7”)

Dimensions in mm

Strap
1253-0-0203

653 (25,7”)
553(21,7”)

655 (25,8”)
Lower edge of wall plate
655 mm (25.8“)

1040 mm (40.9“

Film exit height

1.040 mm (40,9”)

653 (25,7”)

Screw
M4x12
3079-8-5033

Wall break through
for film exit

553 (21,7”)

50 (1,96”)

Blind plate
1176-0-0607

705 mm (27.7“)

553 (21,7”)

All dimensions refer to Protec
base table OPTIMAX
(1267-0-0000)

1.

Wall opening according to drawing.2.

Fasten wallplate with enclosed eight screws (note markings).

3.

Fix blind plate with screws and straps on the film outlet (Detail X).

4.

Push processor up against wallplate and place foam rubber light protection
between processor and wallplate.

5.

Hang in film catch basket at wallplate from the backside.

6.

Check mounting-set for light imper-meability and...