Seguridad

Power and Precision in Perfect harmony
Industrial tools from Fuji

J a p a n e s e e c o - q u a l i t y s i n c e 194 3

Power and Precision in Perfect harmony
Industrial tools from Fuji

For over sixty years, the name Fuji has been synonymous with performance, reliability and quality in industrial tools. Behind this reputation lies a deeply rooted corporate philosophy built oncontinuous learning, customer service and kaizen. These precepts guarantee that every Fuji tool, from the simplest to the most sophisticated, performs its task in perfect harmony with the operator and the industrial process. They also enable us to offer one of the most extensive, most cost-effective ranges of high quality industrial air tools available today.

J a p a n e s e e c o - q u a l i t y s i nc e 194 3

1) Model Number
Use this model number when ordering.

6) Mass
Shows the mass of the tool without accessories.

2) Bolt Size, Capacity
Shows the capacity, which the tool can handle, as guidance for a tool selection. The bolt size of a fastening tool is a bolt size which the tool may fasten. The capacities shown on this catalogue - tapping capacity, riveting capacity, etc.show the size which the tool may handle. Be aware, that the capacity may vary depending on such conditions as the tension, joint rate, material, etc. of the work.

7) Square Drive Size, Bit Shank Size
Square drive size shows the square size of the spindle or anvil of pulse wrenches and impact wrenches. Bit shank size indicates the bit shank size of the driver anvil of screw drivers.

8) Hex.Socket Size
Shows standard hexagonal size of the socket of the ratchet wrenches.

3) Recommended Torque Range, Max Torque
Shows recommended torque range or max torque of the model. Torque figures in the specifications must be used as guidance only, as final output depends on type and size of fastener, joint rate and air pressure etc.

9) Air Inlet Thread Size
Female threaded PT (PipeThreads) and NPT ( National Pipe Threads ) are available.

10) Air Hose Size
The air hose size indicates recommended minimum hose inside diameter which is necessary to supply enough volume of air to the tool for designed performance.

4) Rotational Frequency
Rotational frequency is indicated in revolutions per minute, min-1 at which the tool runs at no load at the working air pressure of 0.63MPa,6.3bar, 90psi if not otherwise specified.

11) Air Consumption
The air consumption of the tools is stated in m3/min, cubic meters per minute. It indicates the maximum air consumption at the working air pressure 0.63MPa, 6.3bar, 90psi if not otherwise stated. Maximum air consumption is valid for the tool without a speed governor when the tool is running at no load.

5) Overall Length
Shows thelongest part of the tool without accessories attached. Refer to the last part of this catalogue "Dimensions" if the details of dimensions are necessary.

Length Diameter, Width, Depth, Height Thickness, Lift, Size Side to Center Capacity Stroke Mass Torque Recommended Torque Range Max. Torque, Measuring Range Stall Torque, Starting Torque Force Lifting Capacity

1m 1 in 1 cm 1 ft

=1000 mm=25.4 mm =10 mm =12 in

=39.4 in =0.0254 m =0.394 in =0.3048 m

=3.28 ft =0.0833 ft =304.8 mm

1 kg 1 lb 1N•m 1 kgf • m 1 ft • lb 1N 1 kgf 1 lbf 1kN 1 Pa 1 bar 1 MPa 1 kPa 1 kp/cm2 1W 1W 1kgf • m/s 1 PS 1 kW 1 m3 1 m3 1 1 ft3 1 m3/s 1 m3/min 1 m3/h 1 m3/min 1 /s 1 cfm 1 m/s 1 ft/s 1 km/h 1 s-1 1 min-1 1 Hz 1 kHz

=1000 g =0.45359237 kg =0.7375 ft • lb =9.807 N • m =1.3558 N • m =0.102 kgf=9.807 N =4.448 N =1000 N =1 N/m2 =100 kPa =10.2kfg/cm2 =0.01 bar =98.07 kPa =0.102 kgf • m/s =1 J/s =9.807 W =75 kgf • m/s =1000 W =35.3 ft3 =1000 =1000 cm3 =28.3 =60 m3/min =35.3 ft3/min =16.667 /min =16.667 /s =2.1189 cfm =0.4719 /s =3.28 ft/s =0.3048 m/s =0.278 m/s =60 rpm =1 rpm =60 bpm =1000 Hz

=2.20462 lb =0.102 kgf • m =7.233 ft • lb =0.138 kgf • m =0.225 lbf =0.205 lbf =0.454 kgf...