Software Variador De Frecuencia

GE
DCT-10 AF-650TM GP, AF-600 FPTM,
& AF-60 LPTM
DCT-10
Operating Instructions
Contents
1 Safety Precautions 3
Connectivity 5
2 Introduction 7
About this Manual 7
What is DCT-10? 7
System Requirements 8
Background Knowledge 8
3 Installation and De-installation 9
Installation and De-installation 9
How to Start the Installation Program 9
4 Introduction to User Interface 11
DCT-10Features 11
5 Set-up of Communication 17
Serial Configuration 19
Profibus DP-V1 Data Communication 20
Profibus DP-V1 Configuration 21
USB Data Communication 22
Ethernet-TSC Data Communication 22
Ethernet-TSC Configuration 23
6 Parameter Handling 25
Set-up 25
Parameter View Settings 30
Filters 30
Parameter Filters 32
Special Parameters 36
Parameter Edit 37
Inline Edit 37
Dialog BasedEdit 38
Comparison of Parameters 38
Read Frequency Converter Database 40
7 Read/Write Parameters 43
Reading and Writing Parameters 43
Read/Write Settings 43
Connection Properties 45
Read From Drive 46
Write to Drive 47
1
Views 48
Scan 48
Scan Configuration 48
Scan Network 49
Poll 49
8 Saving Data 51
Network and Project Folders 51
Changing the Set-up of a Device in the Field 51How to Save Data 51
Save Changes to a Hard Disk 51
Save a Project 52
9 Printing 53
10 Alarm, Warning and Fault Log Readout 55
Localisation of Alarms and Warning 55
Handling Alarms/Warnings in Project Files 57
Handling the Alarms and Warning Trendings 57
11 Scope Function 59
Introduction to the Scope Function 59
Activating the Scope 59
Channel Types 61
Initial "Add Channel" (PC PollingChannel) 62
Communication Control 65
Additional Settings 66
Triggers 69
Trigger Position 69
Cursors 70
12 Update Drives Firmware Support in DCT-10 Set-up 71
How to Find Out if DCT-10 Has Been Updated 72
13 Guide to DP-V1 Connection and Simatic Manager 73
14 Troubleshooting 83
Save Error Dialog 83
Common Problems and Solutions 84
Changes Are Not Saved to PC 84
Error Message WhilstInstalling DCT-10 84
Error Message Communication Failed 84
15 Logic Controller Plug-in 87
2
1 Safety Precautions
1.1.1 Copyright, Limitation of Liability and Revision Rights
This publication contains information proprietary to GE. By accepting and using this manual the user agrees that the information contained herein will be used
solely for operating equipment from GE or equipment from othervendors provided that such equipment is intended for communication with GE equipment over
a PROFIBUS serial communication link. This publication is protected under the Copyright laws.
GE does not warrant that a software program produced according to the guidelines provided in this manual will function properly in every physical, hardware or
software environment.
Although GE has tested andreviewed the documentation within this manual, GE makes no warranty or representation, either express or implied, with respect to
this documentation, including its quality, performance, or fitness for a particular purpose.
In no event shall GE be liable for direct, indirect, special, incidental, or consequential damages arising out of the use, or the inability to use information contained
in thismanual, even if advised of the possibility of such damages. In particular, GE is not responsible for any costs including but not limited to those incurred as
a result of lost profits or revenue, loss or damage of equipment, loss of computer programs, loss of data, the costs to substitute these, or any claims by third
parties.
GE reserves the right to revise this publication at any time and to makechanges in its contents without prior notice or any obligation to notify previous users of
such revisions or changes.
With this software package you can remote-control the frequency converter, thereby starting an electric motor which may act as a drive for
dangerous machinery.
Therefore the necessary caution must always be observed when using the software, and suitable measures should be...