Specification for the power control and monitoring system

SPECIFICATION
FOR THE
POWER CONTROL AND
MONITORING SYSTEM

10/11/98 4:33 PM

SPECIFICATION for
POWER CONTROL AND MONITORING SYSTEM
TABLE OF CONTENTS
Paragraph Title Page

1.0 SCOPE 4
1.1 General 4

1.2 Work to be provided by Seller 4
1.2 The work includes, but not limited to, the items listed below: 4

1.3 Work to be provided by THE BUYER 5
1.3.1Enclosure 5
1.3.2 Cabling 5
1.3.3 Equipment Power 5
1.3.4 Hardware 5
1.3.5 Configuration of Protection Devices 5

2.0 CODES AND STANDARDS 5

3.0 QUALIFICATIONS 7

4.0 TECHNICAL REQUIREMENTS 8
4.1 Description of Services 8
4.2 Design Requirements 8
4.3 Placement 8
4.4 Enclosure (in areas with no environmental control) 8
4.5 Spares 84.6 Warranty 9
4.7 Field Qualify Control (Installation & Commissioning of PCAMS) 9
4.8 Packaging, Shipping, and Storage 10
4.9 Equipment Marking 10
5.0 INSTALLATION 10

6.0 TESTING 11
6.1 Factory Testing 11
6.2 Field Testing (Commissioning Second Phase) 11
6.3 Manufacturer’s Certification 11
6.4 Training 12

7.0 DRAWINGS ANDSUBMITTALS 12

8.0 MANUFACTURING AND PERFORMANCE DATA REQUIRED 13
8.1 Submittals by Seller 13

9.0 TECHNICAL DATA 15
9.1 PCAMS Operations 15
9.2 PCAMS Software 17
9.3 Drawing Graphic Capability 20
9.4 System Component Detailed Specifications 22
9.5 PCAMS Equipment supplied by Seller 24

SPECIFICATION for
POWER CONTROL AND MONITORING SYSTEM

SCOPE1 General

1. This specification covers the furnishing, installation, and testing of a complete, ready-for-operation Power Control and Monitor System (PCAMS).
2. Seller shall bear the responsibility that the equipment has been designed, fabricated, and tested in accordance with all codes, standards, and governmental regulations applicable and performs under the conditions and to thestands specified herein
3. No departure shall be made from codes, standards, regulations, or this Specification unless waived or modified in writing by THE BUYER. Seller shall provide a statement as to compliance with this Specification without exception and/or if there are any exceptions these shall be described in detail and included in Seller’s proposal. Seller shall add a statement that noother exceptions are taken to this Specification

1.2 Work to be provided by Seller

1 The work includes, but not limited to, the items listed below:

a. Furnish, install, and commission a complete, ready-for-use ABB Power RICH System, a Power Control and Monitoring System or THE BUYER approved equal. The PCAMS shall monitor, through metering, all protective devices, analog(4-20ma) devices, and discrete devices (digital on/off). The protective and sensor devices monitored may be in high voltage, medium, and low voltage switchgear and other substation areas. This system shall include, but is not limited to software, IO Server (Host, if only one), network hardware and software for remote communications with other substations and users, UPS, device hardware for the IOServer, communication converters, printers, testing, correcting, startup at site(s), commissioning (testing for customer sign-off), training of operator and administrative personnel, after sale technical support, and graphical screens. All graphical screens and screen transition must be approved via a sign-off by the THE BUYER prior to completion and installation at the customer’s site(s).1.2.2 The work also includes all items necessary or usually supplied for sale, efficient, continuous, and convenient operation of the equipment within the scope of this Specification, whether or not, such items are specially referred to in this Specification.

1.3 Work to be provided by THE BUYER

1 Enclosure See Section 4.4 for Seller specifications

2 Cabling

All...