Tecnico Instrumentacion, Electricidad Y Computacion

！

Installation Guide

Version: 1.1
Date: Dec. 2010

1.Equipment Installation

Warning: No operating with power on!

3.Lock Connection
(1) The system supports NO LOCK and NC LOCK. For example the NO LOCK (normally open at power on) is connected with
’NO’ terminal, and the NC LOCK is connected with ‘NC’ terminal.
(2) When the Electrical Lock is connected to the Access Control System,you need to parallel one FR107 diode (equipped
in the package) to prevent the self-inductance EMF affect the system, do not reverse the polarities.

(I)Share power with the lock:
+

+
+12V
GND

-

11

line hole

-

12

13

DC12V

(2)Remove the screw on the
bottom of device.

(3)Take away the back cover and
waterproof pad.
NC LOCK

-

+

(1)Post the mountingtemplate on the wall.
Drill the holes according to the marks on the
template (holes for screw and wiring).

FR 107

-

+

485485+
GND
BUT
SEN
NO
COM
NC
ALAL+

+12V
GND
485485+
GND
BUT
SEN
NO
COM
NC
ALAL+

DC12V

NO LOCK

-

FR 107

-

10

+

Mounting Paper(only for your reference)

+

Device share power with the lock:
ULOCK=12V, I-ILOCK>1A…… ①
And thelock is near to the device.

(II)Does not share power with the lock:
+

+

485485+
GND
BUT
SEN
NO
COM
NC
ALAL+

(6)Fix the device to the back cover.
DC Power

2. Structure and Function

+

FR 107

-

+
NO LOCK

-

+

+12V
GND

DC12V

+

-

DC12V

(4)Fix the back cover and waterproof pad on the
wall according to the mounting paper.
(5)Set the device tothe fixed waterproof pad.

+12V
GND

NC LOCK

485485+
GND
BUT
SEN
NO
COM
NC
ALAL+

FR 107

+

+

DC Power

Device does not share power with the lock:
A. ULOCK=12V I-ILOCK≤1A;
B. ULOCK≠12V;
C. The lock is far apart from the device.

①: ‘I’: device output current, ‘ULOCK’: lock voltage,’ ILOCK’: lock current.
RS485
RS485

⑥

Access Control System Function:TCP/IP

RS232/RS485
Converter

①
Lock
门锁

②
Door Sensor

④

⑤
EXIT

Card Reader Exit Button

4.Connected with Other Parts:

(1)If a registered user verified, the device will export the
signal to unlock the door.
(2)Door sensor will detect the on-off state. If the door is
unexpected opened or improperly closed, the alarm
signal (digital value) will be triggered.
(3)If thedevice being illegally removed, the device will
export alarm signal.
(4)External card reader is supported.

EXIT

Exit Button

(5)External exit button is supported; it is convenient to
open the door inside.
(6)Supports RS485, TCP/IP modes to connect with PC.
One PC can manage multiple devices.

-

+

-

GND

DC12V

Alarm

Voltage output ≤ DC 12V for Alarm
Alarm

+12VDoor Sensor

+
Alarm Power

③

485485+
GND
BUT
SEN
NO
COM
NC
ALAL+

5.Connected with Power:

Input DC 12V, 500mA (50mA standby)
Positive is connected with ‘+12V’, negative is connected
with ’GND’ (do not reverse the polarities).

The device has the function of Wiegand signal input. It supports
to connect with an independent reader. They are installed each
side of the door, tocontrol the lock and access together.

The device supports standard Wiegand 26 output, as a
reader device it has a very good compatibility.

Access Control

+12V
IWD1
IWD0
RLED
GLED
BEEP
GND

GND
DATA0

+12V
IWD1
IWD0
RLED
GLED
BEEP
GND
WD 0
WD 1

WD 0
WD 1

DATA1

！

7.Wiegand Input

6.Wiegand Output

+12V

9. Communication
There’re two modes that the PCsoftware communicate and exchange information

Terminal

with the device: RS485 and TCP/IP, they all support remote control.

PC Serial Ports

485A
RS485 +
(1) RS485 Mode:
485B
RS485 Please use specified RS485 wire, RS485 active converter and bus-type wiring.
(I) To prevent the interference, the last device in the RS485 bus connect a 120 Euro resistor. That is turning the switch...