Test

Installation and Instruction Manual for
5 Stage Reverse Osmosis System
Purchase Date _____________________
RO Serial Number __________________
Tank Serial Number ________________
Purchased From ___________________
Please read carefully before proceeding with installation
TOOLS & MATERIALS NEEDED
FOR NORMAL INSTALLATION:

PRE-INSTALLATION INSPECTION
After opening, inspect package andlocate the following items:

• Variable speed (VS) drill

1. R.O. Unit

• Carbide grinding burr

2. Storage Tank

• 1/4" (6mm) drill bit

3. Faucet with mounting hardware

• 7/16” (11mm) drill bit

4. Membrane and Flow Restrictor

• 1/2" (13mm) and 5/8” (16mm) open-end
wrenches (or adjustables)

5. Filters
A) Sediment Cartridge
B) Granular Carbon Cartridge
C) Carbon BlockCartridge

• Phillips screwdriver
• Flashlight or droplight
• Teflon tape
• Protective eyewear (i.e.… goggles)
If the above tools are not available, contact
your local distributor for assistance.

REPLACEMENT AND FILTER
CHANGE INTERVAL:
Sediment Pre-filter: 6 months - 1 year
Granular Carbon Pre-filter: 6 months - 1 year
Carbon Block Pre-filter: 6 months - 1 year
R.O. Membrane: 2-4years
Post In-Line Filter: 6 months - 1 year
NOTE: Life of filters and membrane
depends on the quality of water supplied to
the R.O. system.

6. Installation Packet
A) Drain Saddle
B) Tank Ball Valve w/ Tube Insert
C) Tubing
1) Blue for Tank
2)YELLOW for Drain
3) Red for Supply
4) YELLOW for Faucet
D) Easy Adapter and Valve

RECOMMENDATION
If your water hardness exceeds 7 Grains pergallon or 1200 PPM you may consider the
purchase of a water softener for your home.
Contact your local distributor.

DISTRIBUTED BY

OPERATING PARAMETERS
WARNING!! The following conditions for feedwater supply
must be met or the warranty will be void.
1. RO System must be connected to a
municipal or well water source that
is treated and tested on a regular
basis to insurebacteriologically safe
water.
2. Operating Temperatures:
A )Maximum 113° F
B) Minimum 33° F
3. Operating Pressure:
A) Maximum 85 PSI (5.95 kg/cm2)
B) Minimum 40 PSI (2.95 kg/cm2)

CAUTION!! Do not allow RO System to
freeze. The membrane always contains
water and will be destroyed if frozen.
WARNING!! Do not plumb RO System to
hot water. This will destroy the integrity
of system components andvoid the warranty
and manufacturer’s responsibility.
WARNING!! Warranty voided and
manufacturer assumes no responsibility for
damage to system or property if pressure
exceeds 85 PSI. A pressure regulator is
advised to maintain proper presure.

This Reverse Osmosis System is designed to operate at a water pressure in the range of 40 to
80 psi. At pressures lower than 40 psi the quantity aswell as the quality of the water will be
reduced. At higher pressure, severe damage to the system may result. If local water pressure
exceeds 85 psi a pressure regulator must be installed which will reduce the water pressure into
the system.
It is recommended that total TDS (Total Dissolved Solids) does not exceed 2000 ppm
PRODUCT LIBILITY AND WARRANTY INFORMATION
WARNING!! The installer isresponsible for any leaks resulting from installation of tubing or
related fittings. The installer must check over the entire system completely while under
pressure to ensure system is not leaking and is functioning properly. Libility resulting from
failure to check for leaks under pressure is the sole responsibility of the installer.
Each system is Warranted to be free from defects in materialand workmanship for a period of
one year from the date of original purchase. In the event of such defects within the warranty
period, the Manufacturer will, at it's option, replace or recondition the product without
charge. This shall constitute the sole and exclusive remedy for breach of warranty, and the
manufacturer shall not be responsible for any incidental, special or consequential...