Vidalia

�������������������

1.

Table of Contents
1 2~3 4~5 6~9 10 11 14 15 ~ 16 17 ~ 18 19 21 22 23 ~ 36

Table Of Contents 1. Important Information 2. Unit Description 3. Initial Setup 4. How to Splice Wires 5. Harness Diagram 7. VTEC / Idle Control Valve 8. Injector Wires 9. Ignition Signal Wire 10.Analog Input, Output, / Vehicle Speed Signal 12.NVCS / Relay Channels 13.ECU Location Chart14.ECU Wire Locationn Chart

6. Wiring Power, Ground, Airflow Meter, Throttle, RPM signal 12~13

11.Crank & Cam Angle / Water & Intake Temp, Knock Signal 20

1

1.

Important Information

Please read this instruction manual carefully, and proceed with the installation ONLY if you fully understand this manual. Make sure to pay attention to all the "Important!" "Warning!" and "Caution!"messages through out the manual. IMPORTANT! • This product is legal for sale or use in California only on vehicles which may never be driven on a public highway. • This product is only for vehicles with 12V (battery) systems. WARNING! • Installation of this product should only be performed by a trained specialist, who is very familiar with the automobile's mechanical, electrical, and fuel managementsystems. If installed by untrained person, it may cause damage to the unit as well as the vehicle. • Never tune the e-manage Ultimate while the vehicle is moving. • Never tune the e-Manage Ultimate on public highways. This can be dangerous to you and others on the road. • When tuning and operating the vehicle in a garage, make sure that the garage is equipped with a proper ventilation system. •After installation and tuning, make sure to clean up every thing that would interfere the driver. Wires, tools, and laptop computer may interfere with the driver and cause accidents. • Avoid open sparks, flames, or operation of electrical device near flammable substances.

2

1.

Important Information
Caution!

• Improper tuning of the e-Manage Ultimate can cause damage to the engine. •GReddy Performance Products, Inc. will not take any responsibility of damage caused by improper installation or tuning. • Tuning should be performed only by a technician who fully understands the vehicle’s fuel management and ignition timing requirement for the engine being tuned. • Always use a proper air/fuel ratio meter when tuning the e-Manage Ultimate. • Installation of this product requiresmodification of the vehicle’s electrical system. • When making wire connections, be sure to remove the key from the ignition, and disconnect the negative terminal of the battery. • Never short out the system. It can damage the unit as well as the vehicle’s electrical system. • Read and fully understand the wiring diagram before making any wire connection. • When connecting the connector, push it inall the way until you hear them click in together. If there are any questions regarding this products, please contact your GReddy Authorized Dealers or GReddy Performance Products, Inc. 9 Vanderbilt, Irvine, CA 92618

3

4

2.

Unit Description

ACTIVE L.E.D • Steady GREEN - - - - - - When the unit recognize Ignition ON • Flashing GREEN - - - - - When Fouled Plug feature is activated(When engine is started with wide open throttle) • Quick Flashing RED - - - - When Self Diagnostic has detected an error • Flashing RED - - - - - - - When Warning is activated • Flashing Orange - - - - - During Main Unit Data Logging
INTERACTION L.E.D. • Steady - - - - - - - - - - When the unit recognize Ignition ON • Slow Flash - - - - - - - - When confirming engine rpm • Flashing - - - - - - -- - When communicating with PC
DIP SWITCH • Used turn ON/OFF the maps that are set in the Parameter setting (Front Panel)
SWITCH • Used with the Remote Switching System (sold separately) or Switching Harness (Sold separately).
SERIAL • Used to link the GReddy Warning Meters with a Data Link Cable (sold separately)
OPTION1,2 • Used to connect GReddy Pressure Sensor, GReddy Temp Sensor, and/or...