Enetwork Basic Configuration

CISCO NETWORKING ACADEMY - ENetwork Basic Configuration

Page 1 of 10

CISCO CCNA & ITEssentials 2012
QUEST

ENetwork Basic Configuration PT Practice SBA
Add co

CISCO NETWORKING ACADEMY - ENetwork Basic Configuration PT Practice SBA - QUESTIONS
A few things to keep in mind while completing this activity:
1. Do not use the browserBac k button or close or reload any Exam windows duringthe exam.
2. Do not close Packet Tracer when you are done. It will close automatically.
3. Click the Submit Assessment button to submit your work.

Introduction
In this practice Packet Tracer Skills Exam, you will:
finish connecting the devices
design and implement an addressing scheme to meet stated requirements
configure, verify, and troubleshoot connectivity between all devices in thenetwork
Addressing Table

http://blog.smarthand.ro/enetwork-basic-configuration-pt-practice-sba/

5/23/2012

CISCO NETWORKING ACADEMY - ENetwork Basic Configuration

Page 2 of 10

NOTE: The initial network has some errors. To aid in configuring and verifying the devices as well
troubleshooting the existing errors, use a printed version of these instructions to fill inthe missingaddress
information in the table during Step 2.

Step 1: Connect the Devices.
Connect the following devices using the appropriate cable:
a. Connect PC1 to Switch1.
b. Connect Switch1 to the Fa0/0 interface on Router1.
c. Connect Switch2 to the Fa0/1 interface on Router1.
d. Connect PC1 to the Router1 console port.

Step 2: Determine the IP Addressing Scheme.
Design an addressing scheme andfill in the Addressing Table based on the following requirements:
a. Subnet the address space 172.16.1.0/24 to provide 30 host addresses for LAN 1 while wasting the leas
amount of address space.
b. Assign the first available subnet to LAN 1.
c. Assign the lowest (first) host address in this subnet to the Fa0/0 interface on Router1.
d. Assign the second address in this subnet to the VLAN 1interface on Switch1.
e. Assign the highest (last) host IP address in this subnet to PC1.

http://blog.smarthand.ro/enetwork-basic-configuration-pt-practice-sba/

5/23/2012

CISCO NETWORKING ACADEMY - ENetwork Basic Configuration

Page 3 of 10

f. Using the next available subnet, further subnet it to provide 10 host addresses for LAN2 while wasting t
least amount of address space.
g.Assign the lowest (first) host address in the LAN2 subnet to the Fa0/1 interface on Router1.

Step 3: Configure Router1.
a. Configure Router1 with the following basic parameters:
· The router name is Router1.
· The privileged EXEC mode uses the following encrypted password: class
· Enable Telnet and console line login using the following password: cisco
· Configure the bannermessage-of-the-day as Authorized access only!
b. Configure the two Fast Ethernet interfaces, including addressing and a description.
c. Close the terminal window after completing the router configuration.

Step 4: Configure Switch1 and Verify Connectivity.
a. Remove the console connection between PC1 and Router1.
b. Connect PC1 to the Switch1 console port.
c. Configure Switch1 with the following basicparameters:
· The switch name is Switch1
· The privileged EXEC mode uses the following encrypted password: class
· Enable Telnet and console line login using the following password: cisco
· Configure the banner message-of-the-day as Authorized access only!
d.Configure interface VLAN 1 and default gateway for Switch1.

http://blog.smarthand.ro/enetwork-basic-configuration-pt-practice-sba/5/23/2012

CISCO NETWORKING ACADEMY - ENetwork Basic Configuration

Page 4 of 10

e.Switch1 should be able to ping the default gateway.

Step 5: Configure and Verify PC1 Addressing.
a. Using the IP addressing you determined in Step 2, configure PC1 with the correct addressing.
b. PC1 should be able to ping the default gateway.

Step 6: Verify and Troubleshoot End-to-End Connectivity....